|
11-30-2015, 04:39 PM
|
Learning to use the forums
|
|
Join Date: Nov 2015
Posts: 5
|
|
ABS problems 2000 ranger
I have a 2000 Ranger. The ABS wants to kick in after pumping 2-3 times on dry pavement. Then when they kick in its almost like brakes DONT work. It doesn't stop the truck as fast. Feels like its sliding. On snow when the ABS does work on first pump it feels like it too. It feels like ABS stops brakes from working in away. Any comments? Thnak You
|
Register and never see these ads again. |
|
11-30-2015, 06:54 PM
|
Ford Ranger Driver
|
|
Join Date: Oct 2011
Posts: 8,818
|
|
Not supposed to pump the brake pedal. Hold firm pressure without removing your foot from the pedal, until you're stopped. Also, maybe slow down.
|
11-30-2015, 07:35 PM
|
|
Ford Ranger Dismantler
|
|
Join Date: Nov 2014
Posts: 7,008
|
|
Are you 2WD or 4x4? If you're 2WD, take the sensor out of the back of the spindle with an 8mm socket and clean the sensor off. When mine get covered in mud my ABS does funny things. If that doesn't work, take the rotor off and clean the reluctor wheel off.
Quote:
Originally Posted by GLH
Not supposed to pump the brake pedal. Hold firm pressure without removing your foot from the pedal, until you're stopped. Also, maybe slow down.
|
I think his ABS is activating too early is what he's saying.
__________________
2007 Regular Cab - 2.3 DOHC - 5 Speed Auto - 4.10 Gears - Maxtrac 7" Lift - Fiberwerx 3" Fenders - Bilstein 5100 Series - 15x10 Ultra 164's - 35x12.50x15 Red Letters - Custom dents
Quote:
Originally Posted by guell
People like him make me believe that birth control needs to be put in the public water supply
|
|
11-30-2015, 10:48 PM
|
Ford Ranger Driver
|
|
Join Date: Oct 2011
Posts: 8,818
|
|
He's talking about pumping the brakes like he is in a 59 Jimmy. Gotta hold pressure for antilock to work correctly.
|
|
|
|
11-30-2015, 11:32 PM
|
|
Ford Ranger Dismantler
|
|
Join Date: Nov 2014
Posts: 7,008
|
|
I can see it going both ways, GLH. His post isn't very descriptive so it's hard to know what he's asking. This is throwing me off:
Quote:
Originally Posted by rangerinwis
Then when they kick in its almost like brakes DONT work. It doesn't stop the truck as fast. It feels like ABS stops brakes from working in away.
|
Either he's just experiencing normal ABS behavior, or his ABS is kicking in way too early, not allowing more pedal pressure prior to ABS activation, thus not allowing the brakes to function effectively (which happened on my moms former 1998 Windstar and it was scary as shit)
For example, the Windstar, coming up to a steady 5mph stop at a stop sign and the ABS sporadically kicks in and you can't make a gentle stop.
__________________
2007 Regular Cab - 2.3 DOHC - 5 Speed Auto - 4.10 Gears - Maxtrac 7" Lift - Fiberwerx 3" Fenders - Bilstein 5100 Series - 15x10 Ultra 164's - 35x12.50x15 Red Letters - Custom dents
Quote:
Originally Posted by guell
People like him make me believe that birth control needs to be put in the public water supply
|
Last edited by Tyler46; 11-30-2015 at 11:35 PM.
|
|
|
|
|
|
|
12-01-2015, 05:18 AM
|
|
Ford Ranger Driver
|
|
Join Date: Jan 2009
Posts: 6,268
|
|
Re: ABS problems 2000 ranger
Quote:
Originally Posted by Tyler46
I can see it going both ways, GLH. His post isn't very descriptive so it's hard to know what he's asking. This is throwing me off:
Either he's just experiencing normal ABS behavior, or his ABS is kicking in way too early, not allowing more pedal pressure prior to ABS activation, thus not allowing the brakes to function effectively (which happened on my moms former 1998 Windstar and it was scary as shit)
For example, the Windstar, coming up to a steady 5mph stop at a stop sign and the ABS sporadically kicks in and you can't make a gentle stop.
|
GLH seemed pretty clear to me. You do not pump ABS brakes. You hold the pedal steady and the ABS pulses the brakes.
In the snow and ice some ABS systems act totally fubared.
__________________
2004 Ext Cab, 4WD, 4.0, Auto, 154k. (4.0 engine is out of a 2009 Ranger w/96k) ( as of 7/1/2017)
2004 Ranger, Ext Cab, 2WD, 3.0, 5 speed , 4WABS, crank windows, no cruise, Edge 116k.(6/5,2014) (SOLD).
1999 Ford Ranger, Reg Cab, 2.5, 5 speed, 2WD, no AC, 150k (SOLD).
|
|
|
|
12-01-2015, 06:11 AM
|
|
Bringing hell to the city
|
|
Join Date: Feb 2015
Posts: 2,585
|
|
Re: ABS problems 2000 ranger
Ok, with ABS you don't pump brakes, and in winter (especially since you're pumping them) you should remove the ABS fuse - completely disabling ABS.
__________________
Baby Girl: 2006 White Ranger XL with many memories. R.I.P. 1/26/15
Quote:
Originally Posted by Logan03CO
I knew you were an alright guy!
|
Quote:
Originally Posted by ford4thot
The only reason it's worn out junk is because you've gone 70k miles without changing the oil.
|
|
12-01-2015, 07:36 AM
|
Ford Tough
|
|
Join Date: Jul 2011
Posts: 350
|
|
Re: ABS problems 2000 ranger
have experienced what you describe. if you have wheel lockup braking can be greatly reduced. system does not activate properly. if you brake not as heavily you can avoid the problem. would not pull fuse to system. just realize its limitations.
|
|
|
|
12-01-2015, 01:54 PM
|
|
Ford Tough
|
|
Join Date: Aug 2013
Posts: 228
|
|
Re: ABS problems 2000 ranger
Ok, you have 2 reasonable options, fix the problem or unplug abs module, do not just leave it as is if it is preventing you from stopping in any way.
I know of some vehicles that when the abs module is going out it will think the tires are skidding and push back on the pedal making braking impossible, same issue can be caused by sensors though so testing is needed, I'm not sure on the system as my ABS system is different I would assume.
Quote:
Originally Posted by Kealel
Ok, with ABS you don't pump brakes, and in winter (especially since you're pumping them) you should remove the ABS fuse - completely disabling ABS.
|
Yes, this is a good idea, if you are using your truck all the time and are more comfortable just hammering the breaks maybe not, but if you can drive without abs this is a good idea.
Quote:
Originally Posted by bjurke
have experienced what you describe. if you have wheel lockup braking can be greatly reduced. system does not activate properly. if you brake not as heavily you can avoid the problem. would not pull fuse to system. just realize its limitations.
|
From what I understand if your abs is limited stopping capabilities this is a bad idea, braking systems limitations need to be non existent and anything that slows the stopping is a bad thing.
Unplug or fix, personally I'd unplug but its what you feel comfortable with
__________________
1994 Ford Ranger Splash. 4.0L, 4x4, 5 speed. Tracked MPG's - Totalled
1995 Ford Ranger XLT extended cab. 4.0L, 4x4, 5 speed. 2" suspension lift, 3" body lift. 33x12.50r15 bfg rubber on american racing wheels. Tracked MPG's
|
|
|
|
|
|
|
12-01-2015, 02:05 PM
|
|
Ford Ranger Dismantler
|
|
Join Date: Nov 2014
Posts: 7,008
|
|
Quote:
Originally Posted by Kealel
Ok, with ABS you don't pump brakes, and in winter (especially since you're pumping them) you should remove the ABS fuse - completely disabling ABS.
|
Agreed ^^ firm pressure, don't pump.
Quote:
Originally Posted by Jason35
Ok, you have 2 reasonable options, fix the problem or unplug abs module, do not just leave it as is if it is preventing you from stopping in any way. I know of some vehicles that when the abs module is going out it will think the tires are skidding and push back on the pedal making braking impossible, same issue can be caused by sensors though. From what I understand if your abs is limited stopping capabilities this is a bad idea, braking systems limitations need to be non existent and anything that slows the stopping is a bad thing.
|
This ^ is what I'm getting at.
Bad (or dirty) sensors are causing his ABS to not function correctly no matter what the condition of the pavement.
For example, slowly moving through a parking lot with dry ground and when you tap the brakes to stop, the ABS kicks in and you can't make a 2 mph stop.
However his first post was very unclear so we don't know.
__________________
2007 Regular Cab - 2.3 DOHC - 5 Speed Auto - 4.10 Gears - Maxtrac 7" Lift - Fiberwerx 3" Fenders - Bilstein 5100 Series - 15x10 Ultra 164's - 35x12.50x15 Red Letters - Custom dents
Quote:
Originally Posted by guell
People like him make me believe that birth control needs to be put in the public water supply
|
|
|
|
|
12-01-2015, 04:49 PM
|
Learning to use the forums
|
|
Join Date: Nov 2015
Posts: 5
|
|
Re: ABS problems 2000 ranger
I think Tyler46 is dam close to describing/ experiencing my problem. The abs kicks in and I CANT stop. it keeps pushing the pedal back on dry pavemnent. Yes kinda scary at times. Its a habit I have of lightly pumping my brakes as I slow down. I don't pump hard, just slow gentle pumps. I was looking in direction of disconnecting it.(Yes im part redneck..lol) How would a guy do that? Wheres fuse etc? Its snowy and wet in Wis don't feel like working on it in snow..lol THANK YOU everyone who replied. I learned from all you guys.!!Thanks.
|
12-01-2015, 04:58 PM
|
|
Ford Ranger Dismantler
|
|
Join Date: Nov 2014
Posts: 7,008
|
|
Okay cool, haha are you 2WD or 4x4?
__________________
2007 Regular Cab - 2.3 DOHC - 5 Speed Auto - 4.10 Gears - Maxtrac 7" Lift - Fiberwerx 3" Fenders - Bilstein 5100 Series - 15x10 Ultra 164's - 35x12.50x15 Red Letters - Custom dents
Quote:
Originally Posted by guell
People like him make me believe that birth control needs to be put in the public water supply
|
|
12-01-2015, 05:05 PM
|
Ford Ranger Driver
|
|
Join Date: Oct 2011
Posts: 8,818
|
|
I think a smart person would fix the problem and leave the safety feature on.
|
12-01-2015, 05:08 PM
|
|
Bringing hell to the city
|
|
Join Date: Feb 2015
Posts: 2,585
|
|
Re: ABS problems 2000 ranger
The fuse is possibly # 14 or 17, not sure about year 2000, might not be any of those. Worst case you can unplig the wires going to the unit. But for driving in snow, it is best to disable it.
__________________
Baby Girl: 2006 White Ranger XL with many memories. R.I.P. 1/26/15
Quote:
Originally Posted by Logan03CO
I knew you were an alright guy!
|
Quote:
Originally Posted by ford4thot
The only reason it's worn out junk is because you've gone 70k miles without changing the oil.
|
|
12-01-2015, 05:19 PM
|
Learning to use the forums
|
|
Join Date: Nov 2015
Posts: 5
|
|
Re: ABS problems 2000 ranger
Tyler..im in 2wd when this happens.
Kealel..are the wires plugged in front of master cylinder? I have a wire cluster there and I unplugged it. Seems to do the same thing.
GLH..As far as fixing it, where should I start? take out sensors and clean? I will eventually fix it..but its cold and wet out.. my " just so it works" attitude is kicked in..lol
Thanks again Guys..!
|
Thread Tools |
Search this Thread |
|
|
|
|