my 99 hit 166000 km and my lower balljoints are starting to go, i have bought new ones and now i am wondering how hard it is to change them? i have been told to remove the retaining clip and just pound it out, i have also heard the lower control arm needs to be removed. any help would be great. also my truck is a 4x4
thanks

__________________
1999 ranger 4x4 supercab, 4.0L
-3 inch PA body lift
-16 inch pro comp alloys
-33x11.50 BFG all terrain
-Go Rihno roll bar with 4 KC Daylighter lights
-weston bull bar
-dual exhaust,
-air box mod, tightend throttle cable.

you dont have to remove the LCA, just get a BFH and pound the lowers out. its pretty easy to do.

__________________

that seems easy enough
-thanks

__________________
1999 ranger 4x4 supercab, 4.0L
-3 inch PA body lift
-16 inch pro comp alloys
-33x11.50 BFG all terrain
-Go Rihno roll bar with 4 KC Daylighter lights
-weston bull bar
-dual exhaust,
-air box mod, tightend throttle cable.

i recently did this job. i recommend putting the ball joints in the freezer until just before you install them. I did this on one side and it was a hundred times easier installing a cold ball joint compared with a room temp one.

Don't forget to grease those puppies too. If it has a zirc fitting, waiting until they are in is fine, if not add grease before hand. They never put enough grease in them while manufacturing them. Any extra you put in there will ooze out but that's fine. Better too much than not enough.

__________________
Sgtsandman's Work in Progress
2011 Ranger XLT, 4X4, 4 door Super Cab. 4.0L, 5 Speed M50D-R1HD, 3.73:1, 8.8" open differential, Jason Pace cap
2019 Ford Ranger STX FX4, Super Crew, 2.3L Ecoboost, 10 speed automatic, 3.73:1 with rear locker, Leer 100XR cap

got it all done after 6 hours, it was alot more work then i thought it would be.

__________________
1999 ranger 4x4 supercab, 4.0L
-3 inch PA body lift
-16 inch pro comp alloys
-33x11.50 BFG all terrain
-Go Rihno roll bar with 4 KC Daylighter lights
-weston bull bar
-dual exhaust,
-air box mod, tightend throttle cable.

Always is but sooo satisfying when it's done and everything works.

__________________
Sgtsandman's Work in Progress
2011 Ranger XLT, 4X4, 4 door Super Cab. 4.0L, 5 Speed M50D-R1HD, 3.73:1, 8.8" open differential, Jason Pace cap
2019 Ford Ranger STX FX4, Super Crew, 2.3L Ecoboost, 10 speed automatic, 3.73:1 with rear locker, Leer 100XR cap

how much did it cost to do it your self? i have 3 out 4 ripped boots on my truck.

__________________
-1995 ford ranger prerunner, 4.0, 4x4, 5-speed, 62k original miles, 2.5 radflo bypass front and 2.5 radflo triple bypass rear, deavers f23, 4.56 gears front and back, 07 seats, 07 mirrors, 35x12.50 bfg a/t, 4" fiberwerk glass front and rear, eagle alloy rims, 6k hid heads, two 8k hid off road lights, 34" led light bar, bed/roll cage/engine cage, 25 gallon fuel cell, cut and extended beams/radius arms
-2000 ford SVT f150 lightning -SOLD Lifted 2001 Ford Ranger EDGE, April's 2012 TOTM