|
12-24-2017, 01:03 PM
|
|
Ford Ranger Driver
|
|
Join Date: Aug 2015
Posts: 602
|
|
Twisted T-Bars causin Wheel bearing to constantly go...
So because I have 33's and 1.25 inch spacers, the torsion bars are twisted since the previous owner maxed them out by tightening the bolts all the way, now my driver side front wheel bearing is shot... driving home last night I felt it in the steering wheel, heard it, and smelled it, stopped by my firehouse to spray the wheel down with a hose to co it off so it didn't cook any sensors or anything.... so I need to get another wheel bearing, new t bars and have to re cut the wheel studs for the spacers... any advice?
__________________
2001 Ford Ranger Edge 4x4 V6 3.0l Extended Cab
33x12.50x15 Goodyear Wrangler Tires
15x8 American Racing Outlaw 1 Rims
|
Register and never see these ads again. |
|
|
|
|
12-24-2017, 02:04 PM
|
|
Ford Ranger Driver
|
|
Join Date: Feb 2012
Posts: 2,172
|
|
Re: Twisted T-Bars causin Wheel bearing to constantly go...
Quote:
Originally Posted by TexasWalkerRanger
So because I have 33's and 1.25 inch spacers, the torsion bars are twisted since the previous owner maxed them out by tightening the bolts all the way, now my driver side front wheel bearing is shot... driving home last night I felt it in the steering wheel, heard it, and smelled it, stopped by my firehouse to spray the wheel down with a hose to co it off so it didn't cook any sensors or anything.... so I need to get another wheel bearing, new t bars and have to re cut the wheel studs for the spacers... any advice?
|
The hub assembly is pretty easy to replace. The bearing assembly itself is only held in by three bolts and the nut on the end of the CV. You just need to take the caliper and caliper bracket off to get to it, You’ll only need some basic hand tools (socket set, wrenches, breaker bar, etc) and a torque wrench. The axle nut needs to be torqued to 162 ft-lbs.
As for the cause of failure, it’s very unlikely that the sole cause is the tbars being cranked. The front end being out of alignment from cranking the torsion bars may have been a factor, but you could argue that running spacers and 33s was also a factor. Hub assemblies are wear parts, and they go bad. Some sooner than others.
Sent from my iPhone using Tapatalk
__________________
2002 Ford Ranger XLT 4x4, ext. cab, 4.0L v6
Superlifted 33x12.5 Duratracs
1995 Ford Ranger STX 4x4 ext. cab 4.0l v6 SOLD
|
|
|
|
12-24-2017, 07:43 PM
|
|
Ford Ranger Driver
|
|
Join Date: Aug 2015
Posts: 602
|
|
Re: Twisted T-Bars causin Wheel bearing to constantly go...
I just had that side replaced when the motor was rebuilt a couple
Months ago but I'm gonna say that side has more stress because the bar is so twisted on that side that it looks like it's loosened almost all the way... hopefully It'll be easy to do since that side was replaced already and I won't have to worry about anything being rusted.... I had to do the other side myself but now I know what I gotta do :/
__________________
2001 Ford Ranger Edge 4x4 V6 3.0l Extended Cab
33x12.50x15 Goodyear Wrangler Tires
15x8 American Racing Outlaw 1 Rims
|
12-25-2017, 02:05 AM
|
|
Ford Rangers
|
|
Join Date: Jun 2011
Posts: 220
|
|
Re: Twisted T-Bars causin Wheel bearing to constantly go...
Super easy to replace. First time one side took maybe 45min 2nd side closer to 20min
__________________
2001 4x4 stepside, 3"BL, 33" bfg k02, 15x10 clasicII, Custom Catback. UWS LP Toolbox, MOOG suspension comp.,EBC sport rotors, EBC green 7000 pads, Retro`d TRS FX-R 3.0 3" Projectors, CBB 7000K
|
12-25-2017, 11:38 PM
|
9906fordguy
|
|
Join Date: Sep 2017
Posts: 6
|
|
Quote:
Originally Posted by TexasWalkerRanger
So because I have 33's and 1.25 inch spacers, the torsion bars are twisted since the previous owner maxed them out by tightening the bolts all the way, now my driver side front wheel bearing is shot... driving home last night I felt it in the steering wheel, heard it, and smelled it, stopped by my firehouse to spray the wheel down with a hose to co it off so it didn't cook any sensors or anything.... so I need to get another wheel bearing, new t bars and have to re cut the wheel studs for the spacers... any advice?
|
Honestly man, id look into a sas if you can...
__________________
1999 ranger 3.0 4x4
1996 ranger 3.0 4x4
1996 ranger 4.0 4x4
2006 f250 6.0
|
01-03-2018, 04:57 AM
|
|
Ford Ranger Driver
|
|
Join Date: Aug 2015
Posts: 602
|
|
Re: Twisted T-Bars causin Wheel bearing to constantly go...
I wanna do an sas.... but I don know how much that's gonna run me....
----------
Anybody know of any heavy duty or good quality Tbars and were to pick them up?
__________________
2001 Ford Ranger Edge 4x4 V6 3.0l Extended Cab
33x12.50x15 Goodyear Wrangler Tires
15x8 American Racing Outlaw 1 Rims
|
01-03-2018, 12:04 PM
|
|
Ford Ranger Driver
|
|
Join Date: Feb 2012
Posts: 2,172
|
|
Re: Twisted T-Bars causin Wheel bearing to constantly go...
Quote:
Originally Posted by TexasWalkerRanger
I wanna do an sas.... but I don know how much that's gonna run me....
----------
Anybody know of any heavy duty or good quality Tbars and were to pick them up?
|
Ford factory bars, door jamb code “1”. These had the highest spring rate. I’m not aware of any aftermarket options.
You can get new ones through a ford dealer, or used ones from a salvage yard.
Sent from my iPhone using Tapatalk
__________________
2002 Ford Ranger XLT 4x4, ext. cab, 4.0L v6
Superlifted 33x12.5 Duratracs
1995 Ford Ranger STX 4x4 ext. cab 4.0l v6 SOLD
|
01-10-2018, 01:25 PM
|
|
Ford Ranger Driver
|
|
Join Date: Aug 2015
Posts: 602
|
|
Re: Twisted T-Bars causin Wheel bearing to constantly go...
How much would they rape me- I mean run me for them if I get them through the dealership...
__________________
2001 Ford Ranger Edge 4x4 V6 3.0l Extended Cab
33x12.50x15 Goodyear Wrangler Tires
15x8 American Racing Outlaw 1 Rims
|
01-10-2018, 01:27 PM
|
|
Still around
|
|
Join Date: Jun 2012
Posts: 2,298
|
|
Re: Twisted T-Bars causin Wheel bearing to constantly go...
Rape with no lube. Try to avoid the dealer, #1 torsion bars from a salvage yard are the way to go ‘98-‘11 will work
Sent from my iPhone using Tapatalk
__________________
2011 Ranger XLT 4x4 3.73 8.8" Trac-lok #1 T-bars, K -springs, LineX bedliner, General Grabber AT2's, Tonnopro tri-fold, CoverKing Realtree AP seat covers, OEM pre-keys, axle spacers, Bilstein 4600's, Hellwig AAL. Ziebart Undercoat
'98 Ranger XLT 2WD (sold)
|
01-11-2018, 07:21 AM
|
|
Ford Ranger Driver
|
|
Join Date: Aug 2015
Posts: 602
|
|
Re: Twisted T-Bars causin Wheel bearing to constantly go...
I figured that... I'll start looking around and see what I can find
__________________
2001 Ford Ranger Edge 4x4 V6 3.0l Extended Cab
33x12.50x15 Goodyear Wrangler Tires
15x8 American Racing Outlaw 1 Rims
|
Thread Tools |
Search this Thread |
|
|
|
|