Ford Ranger Forum - Forums for Ford Ranger enthusiasts!

Go Back   Ford Ranger Forum - Forums for Ford Ranger enthusiasts! > >
Forgot Password? Join Us!

Welcome to Ford Ranger Forum

Thread Tools Search this Thread

Old 04-10-2010, 10:04 AM
drewglenn04 drewglenn04 is offline
Ford Ranger Driver
Join Date: Dec 2009
Posts: 78
Question Shocks - Twin Tube vs. Monotube

Im gonna be makin a purchase soon. Whats the difference between these two types of shocks?

2002 XLT Ext. Cab
4x4 Off Road 4.0L

Fog Light Mod, Throttle Mod, Torsion Bars Cranked
265/75/R16 Tires, Air Silencer Removal Mod
Reply With Quote
Old 04-11-2010, 08:54 AM
Tom Tom is offline
Ranger Enthusiast
Join Date: Nov 2008
Posts: 6,826
Default Re: Shocks - Twin Tube vs. Monotube

This might help...

Bring on the Dampers
Shock absorbers, more properly called dampers, are mounted alongside (or inside) the springs at each corner of the vehicle. A shock absorber's job is to provide resistance to the movement of the spring. Technically speaking, it does this by taking some of the energy that is being used to compress the spring and turning it into heat. So whether the vehicle is bouncing up or down from a bump in the road, that motion is held in check by the shock absorber, and once again some of the kinetic energy released by the spring is changed into heat by the shock absorber. This conversion of energy keeps the vehicle's body from bouncing more than once or twice, providing a controlled ride and helping to keep the vehicle's tires safely in contact with the ground.

But How?
If you have ever waved your hand back and forth through water, then, in principle, you know how a shock absorber works. The resistance to motion you feel with your hand changes with speed – the faster you move your hand, the more energy it takes to push against the resistance of the water.

A shock absorber works much the same way. Inside the shock absorber there's a piston that moves inside a tube which is filled with oil. As the piston moves, the oil is forced through tiny holes and valves within the piston, precisely controlling the amount of resistance to movement. This resistance to the motion converts the energy into heat. (Yes, a shock absorber that has been doing its job over a rough road does get warm!)

What Types?
Although there have been many different designs for shock absorbers over the course of automotive history, today there are four basic types available:



Gas-filled mono-tube

External reservoir

Sometimes these types of shock absorbers are incorporated into a strut-type suspension that uses the shock absorber as part of the spring support, but the basic principles still apply.

The twin-tube design is the most common and often times the least expensive. These are the ordinary shock absorbers that typical passenger cars and trucks use, and they are widely available at car dealerships, auto parts stores and repair facilities. As the name implies, in a twin-tube shock, there are two actual tubes – one the outer shock body and the other a cylinder inside in which the piston moves. Tiny holes or orifices in the piston as well as special valves between the inner and outer tubes restrict the flow of oil to control wheel motion.

The limitations of twin-tube shocks become apparent when they are used over very bumpy roads. In this case, the rapid motion of the piston can cause the oil to overheat and to foam, reducing the shock absorber's ability to control wheel motion. The result is a ride that becomes increasingly sloppy, especially when traveling over a washboard surface. Heavy-duty twin-tube shock absorbers are usually stronger, with more robust piston shafts and mounting points, and they may use oils that are more resistant to foaming, but ultimately they still have the same limitations.

Mono-Tube and Gas-Filled Shocks
The heat generated in the twin-tube shock tends to get trapped within the walls of the shock absorber body, reducing its effectiveness in controlling wheel motions. The mono-tube shock absorber uses a piston traveling within a single tube that is exposed more directly to the air. The general advantages and disadvantages of this design are:

By getting rid of heat more easily, mono-tube shocks are less susceptible to overheating on rough roads.
They are more expensive to manufacture however, and the tolerances must be higher and the seals better to keep the oil inside the shock body.
To prevent foaming and bubbles in the oil, which degrades shock-absorber performance, a gas-filled mono-tube shock has a chamber of high-pressure nitrogen above the oil chamber. This high-pressure gas makes it difficult for bubbles to form in the oil, even when the shock absorber moves in and out very quickly, as it might while traveling rapidly on a very rough or washboard road.

Gas-filled shocks are expensive, since they require strict manufacturing tolerances, but they are very resistant to fade and consequently are popular in off-road racing and rallying. Gas-filled shocks, by the way, are not the same as "air shocks" which use an air chamber separate from the shock oil. An air shock is actually an air spring that raises or lowers the vehicle when air is added or removed through a valve.
2006 Ford Ranger Sport 4.0 2WD on 32x11.50R15s
-3" Doetsch Spindle Lift

Using the forum:
How to Post on the Forum
Creating a signature (do this before asking any questions)
Upload an Avatar (image of your Ranger)
How to Post Pictures on the Forum
Switch the site layout: Light Theme or Dark Theme

Things to do:
Participate in Truck of the Month
Participate in the Ranger Photo Contest
Participate in the Non-Automotive Photo Contest
Become a Site Contributor
Shop at the Store
Reply With Quote

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Similar Threads
Thread Thread Starter Forum Replies Last Post
Twin cities, minnesota RangerLuc Off Topic 10 04-07-2010 06:26 PM
Used to be my twin dixie_boysles Vehicle Snapshots 19 02-20-2010 08:37 PM
Twin supercharged ford ranger 5.0l bruzer59 Vehicle Videos 13 12-31-2009 10:50 AM
the ranger's twin brothers goes to rest greyghost Off Topic 10 09-19-2009 11:00 AM
Twin I beam aleal Suspension Tech 2 06-18-2009 05:46 AM