Forum: General Tech
06-05-2013, 04:52 PM
|
Replies: 2
Views: 988
P-1131 trouble code
Our 1999 ranger 2.5 can't pass the emissions test and shows a trouble code of P1131 -Anybody got any ideas other than taking it to a dealer and getting ripped--Thanks in advance Rich
|
Forum: General Tech
12-23-2012, 01:02 PM
|
Replies: 4
Views: 1,069
Re: 99 ranger
That lil ranger is actually my second -it is a 2000 2.5 4cyl-5 speed that I haul our ATV around behind our MH-I made the flat bed which has a winch to pull the ATV's up the ramps then I can drive...
|
Forum: General Tech
12-23-2012, 07:52 AM
|
Replies: 4
Views: 1,069
99 ranger
!999 ranger/4.0/4 x 4/auto-207k miles
My ranger will sometimes crank over well but not start-retrying it a few times will fire it right up like a new car--I changed the ign module under the dash...
|
Forum: Interior Tech
09-07-2012, 06:01 PM
|
Replies: 1
Views: 647
Cruise control broke
The cruise control buttons on the right read- set-resume-coast-broke so I ordered a new one 80 bucks from dealer (OUCH) but after I disconnected the battery I put the neg & pos wire on bat together...
|
Forum: General Ford Ranger Discussion
12-31-2011, 03:49 PM
|
Replies: 9
Views: 1,806
Re: ATV on top?
I took the bed off my 2000 ranger and made a flat bed similiar to a snow mobile trailer to haul our two ATV's behind our Motorhome works great -If you want more details and pics -I'm at...
|
Forum: General Ford Ranger Discussion
12-31-2011, 02:52 PM
|
Replies: 13
Views: 1,299
2000 heat response
My 2000 ranger had the problem of having only one speed left on heater fan-Sure as s__t it was the resistor and plug both rusted to hell --replaced resistor and made my own plug works great!!!!- Also...
|
Forum: General Ford Ranger Discussion
11-15-2011, 02:22 PM
|
Replies: 1
Views: 1,233
heater/defroster
2000 ranger / 2.5 / 5 sp
When I change heat control it stays on defrost-I think defrost is default and I thought vacumn made it change -Any help appreciated-Rich
|
Forum: General Ford Ranger Discussion
11-14-2011, 06:50 AM
|
Replies: 3
Views: 1,173
|
Forum: General Ford Ranger Discussion
08-16-2011, 08:10 PM
|
Replies: 3
Views: 1,173
4 wheel vacuum sucks
I am throwing the vacuum 4wheel system in the garbage can and adding AVM manual locking hubs--anybody done this on 1999 ranger-what is all envolved-l have taken everything apart since I can't draw...
|
Forum: Drivetrain Tech
03-09-2010, 07:08 AM
|
Replies: 0
Views: 1,937
99 ranger rear end whine
I am going to tackle putting in rear dif input bearings and carrier bearings I already replaced both axles & axle bearings so the whine must be one of these other bearings-I can't find any good...
|
Forum: Drivetrain Tech
02-27-2010, 09:47 AM
|
Replies: 0
Views: 1,060
1999 ranger rear end
I have been putting up with whining noise coming from rear end-plan on tackling job changing input shaft bearings & outputshaft bearings (already changed rear axle bearings and axles) Anybody got...
|
Forum: 4.0 SOHC / 4.0 OHV Tech
01-29-2010, 03:49 PM
|
Replies: 1
Views: 2,167
1999 ranger 4.0
Does anybody know how to reset computor so the CHECK ENGINE light will go out-I thought that if you disconnect the battery and then reconnect it would do the trick but only for a short time-I have...
|
Forum: General Ford Ranger Discussion
01-08-2010, 06:29 AM
|
Replies: 1
Views: 1,284
1999 ranger 4.0 IDLE
I have a 1999 ranger 4x4 with 4.0 -problem being idle sits at about 1200- 1300rpm at idle and it should be 750-800 at a corner with deep snow it is hard to slow down because of fast idle -Any...
|
Forum: Electrical Tech
01-04-2010, 09:28 AM
|
Replies: 116
Views: 69,493
instrument cluster
After removing the two 7mm screws from radio cluster cover plastic wouldn't come off (same with cluster cover) is there pins or something that hold plastic on or is there a special tool to get the...
|