Ford Ranger Forum - Forums for Ford Ranger enthusiasts!

Go Back   Ford Ranger Forum - Forums for Ford Ranger enthusiasts! >
Reload this Page Search Results
Forgot Password? Join Us!
FRF Store Register Ranger Pictures Members List Social Groups Search Today's Posts Mark Forums Read

Welcome to Ford Ranger Forum

Showing results 1 to 22 of 22
Search took 0.00 seconds. Search: Posts Made By: deliveryRANGER
Forum: General Tech 09-19-2012, 10:31 AM
Replies: 9
Views: 1,431
Posted By deliveryRANGER
Re: Lack of heat

make sure you got an oem temp thermostat. it you hear it clicking its a good part.
Forum: 4.0 SOHC / 4.0 OHV Tech 09-19-2012, 10:21 AM
Replies: 7
Views: 4,052
Posted By deliveryRANGER
Re: bleeding slave cylinder... 2000 ford ranger 4.0L V6, manual tranny, 4X4

you can take the system from fill reservoir to quick disconnect line on side of trans off. once off bleed the air out. do not have to have a vacuum it just makes job alot easier.
Forum: 4.0 SOHC / 4.0 OHV Tech 09-16-2012, 01:20 PM
Replies: 7
Views: 4,052
Posted By deliveryRANGER
Re: bleeding slave cylinder... 2000 ford ranger 4.0L V6, manual tranny, 4X4

for pilot we just took the flywheel out. outer ring on the shaft holding throw out bearing, it takes patience but find the end and it will split
Forum: General Tech 09-11-2012, 11:57 AM
Replies: 2
Views: 1,706
Posted By deliveryRANGER
Re: Water leaking into pass side above fuse panel

pass side? my fuse box is on drivers. If it is passengers side, have you checked coolant system? Heater core is in that area and could have a leak.
Forum: Electrical Tech 09-07-2012, 11:47 AM
Replies: 4
Views: 945
Posted By deliveryRANGER
Re: Ignition no start

ever hear back from the dealer?
Forum: Electrical Tech 09-06-2012, 11:39 AM
Replies: 18
Views: 2,409
Posted By deliveryRANGER
Re: no power to starter after mishap

yest afternoon after work i re-wrapped that harness and bolted everything up. fired up immediately. the voltmeter is a cheapo from autozone i got it for 10 bucks so i doubt it s the most accurate...
Forum: 4.0 SOHC / 4.0 OHV Tech 09-04-2012, 07:51 PM
Replies: 7
Views: 4,052
Posted By deliveryRANGER
Re: bleeding slave cylinder... 2000 ford ranger 4.0L V6, manual tranny, 4X4

i just did this after installing a new slave and clutch on a 3.0 i hope its the same trans . there is a small valve on the driver side of the trans it looks identical to the one on a caliper, its...
Forum: Electrical Tech 09-04-2012, 07:35 PM
Replies: 18
Views: 2,409
Posted By deliveryRANGER
Re: no power to starter after mishap

HOLY MOTHER OF MOSES


well after another grueling day i finally found my issue...... The #56 starter relay's ground wire. with a voltmeter i found the constant hot. then switched to ohms to...
Forum: Electrical Tech 09-04-2012, 05:09 PM
Replies: 18
Views: 2,409
Posted By deliveryRANGER
Re: no power to starter after mishap

I got home today and was going to test the wires. i know that the constant power wire going to the starter is good. But today i tested the small wire, at the very end of the wire where it connects...
Forum: Electrical Tech 09-03-2012, 07:54 PM
Replies: 18
Views: 2,409
Posted By deliveryRANGER
Re: no power to starter after mishap

ok i have ruled out batt problem and connection problems. Gonna check the small remote wire when i get home from work, i am almost positive this or were it leads is my issue. thanks for the help btw
Forum: Electrical Tech 09-03-2012, 06:25 PM
Replies: 18
Views: 2,409
Posted By deliveryRANGER
Re: no power to starter after mishap

just got back from autozone and had them test batt. 87%.

was wondering if the 2003 model had a remote solenoid
Forum: Electrical Tech 09-03-2012, 03:04 PM
Replies: 18
Views: 2,409
Posted By deliveryRANGER
Re: no power to starter after mishap

i can take same batt and put it in a different truck and it fires up. plus my battery charger says 14.2v. i ran jumper cables to starter and the negative batt post to ground it while leaving the...
Forum: Electrical Tech 09-03-2012, 01:51 PM
Replies: 18
Views: 2,409
Posted By deliveryRANGER
Re: no power to starter after mishap

i just used the batt in my truck today to go get the starter. his batt has been sitting for a week and needs to be charged but mine is an every day driver. i thought it might be a connection issue...
Forum: Electrical Tech 09-03-2012, 01:34 PM
Replies: 18
Views: 2,409
Posted By deliveryRANGER
Re: no power to starter after mishap

batt is good i been using the one from my truck :P the batt is a month old but yea thats the noise i am hearing. it sounds exactly like a bad batt or bad starter both are new. connections are clean...
Forum: Electrical Tech 09-03-2012, 12:44 PM
Replies: 18
Views: 2,409
Posted By deliveryRANGER
Re: no power to starter after mishap

i bypassed the large wire so i know that is not my issue. the small wire has the relay in the back of the power box #56 and a 50a fuse same box #11. i have changed these out with parts from my...
Forum: Electrical Tech 09-03-2012, 12:33 PM
Replies: 18
Views: 2,409
Posted By deliveryRANGER
Re: no power to starter after mishap

today i have run a ground wire from starter bolt to frame and didnt solve issue. i then ran jumper cable from hot wire to starter to batt to eliminate the chance the wire burned. i am thinking i...
Forum: Electrical Tech 09-02-2012, 05:48 PM
Replies: 18
Views: 2,409
Posted By deliveryRANGER
no power to starter after mishap

i was helping little brother work on his truck when we had a little mishap. After we removed the starter the pos and neg wires grounded out on oil pan. i have checked the fuses and relays in both...
Forum: Drivetrain Tech 08-28-2012, 09:46 AM
Replies: 4
Views: 3,807
Posted By deliveryRANGER
Re: Need help/guide with Front wheel hub assembly

man you got the idea. You just explained every step only thing you are missing is a 32mm for the spindle nutt and do not grease it. It's a sealed hub, the bearing is inside. comes with a new abs...
Forum: 4.0 SOHC / 4.0 OHV Tech 08-12-2012, 03:08 PM
Replies: 2
Views: 1,005
Posted By deliveryRANGER
Re: #4 cylinder misfire on start up

sorry taken so long to reply had my sons b day party. Last time i had codes ran i think it was 2 codes. A random misfire #4 cylinder on start up and a random misfire code. I will stop by a friends...
Forum: 4.0 SOHC / 4.0 OHV Tech 08-10-2012, 11:00 AM
Replies: 2
Views: 1,005
Posted By deliveryRANGER
#4 cylinder misfire on start up

truck runs great but the check engine light been on since i bought it. Replaced coil, plugs and wires change fuel filters regularly. Dealership told me it may be some air in evap system from...
Forum: Drivetrain Tech 08-10-2012, 10:48 AM
Replies: 2
Views: 1,589
Posted By deliveryRANGER
broken quick disconnect line to slave... help plz

hello all, a buddy needed a new clutch so i told him i would help out. His truck is a 96 Mazda b400, which is the same as a 96 ranger 4x4 4.0. we got the new clutch in but when we were taking the...
Forum: Introduce Yourself 11-08-2011, 06:37 AM
Replies: 13
Views: 839
Posted By deliveryRANGER
new member usps ranger

hello all,

Justin here i am 25 checking in from the woods of Mississippi. i work in some pretty rural areas and needed something rugged and reliable so i got my ranger about a year ago and...
Showing results 1 to 22 of 22