2000 Ford Ranger - P1151, P1152, P0306, P0175
Just the other day my 2000 4.0L Ranger XLT started running rough, I have pulled the codes and have got :
P1151 P1152 - Pending P0306 P0175 when I tested it at first the code P0306 never showed up, it showed up after I cleared out the original codes. my Freeze frame information is as follows : DTCFRZF ----- P0306 Fuelsys1 ------CL FuelSys2------N/A Load %-------80.4 ETC (degres C) 93 Shrtft1 (%)---- 1.6 Longft1(%)---- -0.8 Shrtft2 (%)--- 42.2 Longft2 (%)---- -2.3 RPM (/min) ---- 1686 VSS (km/h) 84 My symptoms are bucking and jarring under any load, and significant loss of power, I thought it may have been my downward O2 Sensor but I changed that out and it was fine, I took out my #6 plug and that did nothing. I checked my MAFS and it is fine as well. Any help would be greatly appreciated. |
Man I have the SAME stuff but I've kinda gotten rid of it I'll turn off my truck when in starts and turn it back on, but also I have had my motor replaced, and I had all the same symptoms with it too and they came back ive rand new wires, spark plugs, and on my 3rd coil pack and my trucks a '99 so it's the same model as stuff as yours.
|
Re: 2000 Ford Ranger - P1151, P1152, P0306, P0175
Quote:
If your scanner will give live data, you can see what your down steam O2 sensor is doing too. The down steam sensor is more of a Catalyst monitor than a O2 sensor though. |
Yeah I've replaced my O2 sensors and it did nothing, they said its probably my cats but them jokers are way to expensive to buy because it "might" be the problem
|
Re: 2000 Ford Ranger - P1151, P1152, P0306, P0175
Hey Guys,
Thanks for all your help, I replaced all my plugs last night and I got rid of the miss fire code, and now I just have the "rich bank 2 code" I have checked my vacuum lines, replaced my #2 O2 sensor. I was going to check my compression in cylinder 6 this weekend but I won't have time. I have checked the compression a few times in the past and it all seems to be fine, I have had a similar problem to this before but a simple change of the plugs worked last time. Does anyone know a way to check an O2 sensor?? |
Re: 2000 Ford Ranger - P1151, P1152, P0306, P0175
Quote:
Were you able to get rid of the missfires? |
Re: 2000 Ford Ranger - P1151, P1152, P0306, P0175
there really isnt a way, id just but a new one. relatively cheap.
|
Re: 2000 Ford Ranger - P1151, P1152, P0306, P0175
Quote:
See this post: http://www.fordrangerforum.com/4-0-s...6768-help.html |
Smell of sulfur = plugged catalytic converter
|
Re: 2000 Ford Ranger - P1151, P1152, P0306, P0175
Quote:
Mechanic this morning hooked up a snap-on ODBII scan tool. Like a mini PC with a touchscreen. 2 codes were present in the Engine section. P sum-thing o2 sensor 1 is Rich P sum-thing 02 sensor 2 is Lean o2s21 5-6 mv o2s22 1-3 mv MAF (v) 0.02 volts He set the scanner to read live data and determined that Cylinder 1 was missing intermittently and cylinder 6 would miss every 20 seconds or so randomly. I swapped plug wires with cyl 1 and 2 no change o2 voltage was present and seemed to be working fine (both sensors are under a year old) Come on guys, help me out. A car payment (2010 or newer) and no headache sounds good right now but I can't give up yet ---------- Edit: also the SFTRIM 2(%) was at 14% and the LFTRIM 2(%) was at 0% Does any of this help? My mechanic says either new sending unit ($200) or a set on injectors ($alot) unless I have any other ideas. I cannot keep throwing money at it like a hot stripper here. HELP! |
Try swapping plugs. a bad cylinder with a known good one and do the same with the injectors just dont swap one from the same good cylinder as the spark plug swap. Does that make sense?
|
Ive also seen this in a failing coil. Have you tried my previous suggestion yet?
|
Re: 2000 Ford Ranger - P1151, P1152, P0306, P0175
Quote:
I swapped plugs with good Cylinders. Miss seemed to go away until I went up a small hill and it was back to dog'n again and consuming double the gas it should. Hooked up a gauge to fuel rail nipple. Book says between 58 and 72 psi. It has 62 at Idle and 60 psi at 3500 RPM, no big drop while pegginh the gas pedal.. It is getting gas, air and spark. Why the intermittent mis-fire on cyl 1 and 6? New coil and plugs and wires already sit in the money pit. I also have the original coil that came with the truck.(tests good) TPS is due in Monday but I do not think it will help. ANY IDEAS here guys? |
One last ghing brgore im out of ideas. starg hour truck and let it run for a minute. Then shut it off and pull the hose of the vacuum brake booster to see if there is vacuum pressure
|
Re: 2000 Ford Ranger - P1151, P1152, P0306, P0175
Quote:
|
All times are GMT -7. The time now is 08:40 PM. |