How To: Deactivating/activating the BeltMinder feature (seatbelt chime)
FordRangerForum.com and I do not take any responsibility for injuries/death in accident because seat belt was not worn. You should always wear your seat belt
Discussion Thread:How To: deactivating activating beltminder feature (seatbelt chime) Deactivating/activating the BeltMinder feature Read steps 1 - 9 thoroughly before proceeding with the deactivation/activation programming procedure. The BeltMinder feature can be deactivated/activated by performing the following procedure: Before following the procedure, make sure that: The parking brake is set. The gearshift is in P (Park) (automatic transmission) or the neutral position (manual transmission). The ignition switch is in the OFF position. All vehicle doors are closed. The drivers safety belt is unbuckled. The parklamps/headlamps are in OFF position (If vehicle is equipped with Autolamps, this will not affect the procedure). 1. Turn the ignition switch to the RUN (or ON) position. (DO NOT START THE ENGINE.) 2. Wait until the safety belt warning light turns off. (Approximately 12 minutes.) Steps 35 must be completed within 60 seconds or the procedure will have to be repeated. 3. Buckle then unbuckle the safety belt three times, ending with the safety belt unbuckled. This can be done before or during BeltMinder warning activation. 4. Turn on the parklamps/headlamps, turn off the parklamps/headlamps. 5. Buckle then unbuckle the safety belt three times, ending with the safety belt unbuckled. After step 5 the safety belt warning light will be turned on for three seconds. 6. Within seven seconds of the safety belt warning light turning off, buckle then unbuckle the safety belt. This will disable BeltMinder if it is currently enabled, or enable BeltMinder if it is currently disabled. 7. Confirmation of disabling BeltMinder is provided by the safety belt warning light flashing four times per second for three seconds. 8. Confirmation of enabling BeltMinder is provided by: The safety belt warning light flashing four times per second for three seconds. Followed by three seconds with the safety belt warning light off. Once again, the safety belt warning light will flash four times per second for three seconds. 9. After receiving confirmation, the deactivation/activation procedure is complete. |
2009 Instructions
The driver and front passenger Belt-Minder are deactivated/activated independently. When deactivating/activating one seating position, do not buckle the other position as this will terminate the process. Read Steps 1 - 4 thoroughly before proceeding with the deactivation/activation programming procedure. Note: The driver and front passenger Belt-Minder features must be disabled/enabled separately. Both cannot be disable/enabled during the same key cycle. Before following the procedure, make sure that: • The parking brake is set • the gearshift is in P (Park) (automatic transmission) or the neutral position (manual transmission) • The ignition switch is in the off position • The driver and front passenger safety belts are unbuckled 1. Turn the ignition switch to the on position. DO NOT START THE ENGINE. 2. Wait until the safety belt warning light turns off (Approximately one minute). • Step 3 must be completed within 50 seconds after the safety belt warning light turns off. 3. For the seating position being disabled, at a moderate speed, buckle then unbuckle the safety belt nine times, ending in the unbuckled state. Step 3 must be completed within 50 seconds after the safety belt warning light turns off. • After Step 3, the safety belt warning light will be turned on for three seconds. 4. Within approximately seven seconds of the light turning off, buckle then unbuckle the safety belt. • This will disable the Belt-Minder feature for that seating position if it is currently enabled. As confirmation, the safety belt warning light will flash four times per second for three seconds. • This will enable the Belt-Minder feature for that seating position if it is currently disabled. As confirmation, the safety belt warning light will flash four times per second for three seconds, followed by three seconds with the light off, then followed by the safety belt warning light flashing four times per second for three seconds again. |
All times are GMT -7. The time now is 06:23 AM. |