Ford Ranger Forum - Forums for Ford Ranger enthusiasts!

Go Back   Ford Ranger Forum - Forums for Ford Ranger enthusiasts! > > >
Forgot Password? Join Us!

Welcome to Ford Ranger Forum

Closed Thread
Thread Tools Search this Thread

Old 08-17-2009, 05:24 PM
STL STL is offline

Join Date: May 2009
Posts: 23,399
Default How To: 2004 and up Mustang Dome Light Mod

Discussion Thread: How To: 2004 and up Mustang Dome Light Mod

If you have a 2001-2003 it is a direct swap no need to add power wire
Unless your truck is a 2004 and up these instructions do not apply to you.

***Some 2004 Trucks are also plug and play. Only the early model year trucks. If you remove your factory dome light and you see 2 factory wires there you are good to go, and dont need to add a power wire.

Tools needed:
  • Philips & small flathead Screwdriver
  • 9/32" 6 point socket/rachet
  • Replacement Dome Light (From Mustang/Explorer/F-Series etc)
  • 3 screws (should come with new dome light, or you can match one to the two in your current dome light)
  • 1 Wire Tap
  • About 8 feet of wire
  • Electric tape
  • Electrical Fish tape (not required but helpful)

Step 1: Remove existing dome light.
Pop off the plastic cover with a small flathead. Then take out the two philips screws and the old dome light should be off.

Step 2: Removing trim.
You have to run power from the headlight switch to the dome light.
Start by taking off the dash access panel

Remove the grab handles on the A-pillar. This is accomplished by first removing the plastic trim plugs to expose the 9/32" hex bolts

Now you can pull off the A-Pillar trim piece. there are 2 plugs that hold this trim in place. Just pull the trim straight down towards the seat and it'll pop out. Just take your time

Remove the 3 Phillips screws that hold the sun-visor in place. After removing them, you should be able to drop the corner of the headliner, allowing you to run the wiring

You should now have a clear shot to run the wiring. Start from behind the headlight switch, up the a-pillar, tucking the wire behind the rubber strip to hold it into place then through the headliner and to dome light. This is where the wire snake would come in handy to run the wire to the dome light opening
Those with high powered subwoofers may want to take this time to secure the power wire with plenty of tape and/or wire ties. I had to secure mine in many places because it caused a few annoying rattles when the sub hit.

Step 3: Running the constant power wire.

Standard disclaimer: Caution, you can shock yourself, cause a fire and/or blow some fuses if you don't do this right, so be safe and disconnect the battery. and the author of this how to are not responsible for any damage or injuries.

Locate the Green wire with Orange Stripe behind the headlight switch. This is the wire missing behind the dome light on 2004 and newer Rangers. This wire is "behind" the power saver relay, which means this wire will deliver constant power for approximately 10 minutes without a key in the ignition. If you want constant power without any interruptions, you will need to run a line from the battery (with fuse) or tap into the fuse box (passenger kick panel).
Use a wire tap to splice into the Green/orange wire

Now you want your new power wire to connect to the screw circled in Black. The RED circle is for switched power and this hole should line up with the black/blue wire Ford put behind the dome light. As stated before, the ground is the chassis. Just make sure the last screw hole circled in yellow lines up with a pre-drilled hole into the dome light brace.

Black = Constant
RED = Switched
Yellow= Ground

Step 4b: Mounting the light.
By using the screws for ground and switched power (screwed to the factory locations)
should be sufficient for a secure mount.

Step 5: Test the installation.
CHECK ALL WIRING. Make sure all dome light screws are contacting the factory wire, your power wire, or the chassis. Make sure the wire tap is in contact with the wire.
Reconnect the battery.
Close all doors to reset the battery saver relay. Then turn the rotary dial by the headlight switch to turn on the dome light. The center bulb should illuminate. Turn the switch back to "off".
Test the map light switches on the dome light. Each switch should turn on one bulb and one bulb only. It should be obvious which one that it. These map light switches should work independently of the headlight dome switch, because of the power wire you ran.

Step 6: Replace trim.
Follow step 2 in reverse order

2005 Edge

Last edited by STL; 06-13-2011 at 03:20 PM.
Closed Thread

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Similar Threads
Thread Thread Starter Forum Replies Last Post
Discuss 2004 and up Ranger to Mustang Dome Light Mod STL How-To Submissions 155 12-28-2016 10:03 AM
airbag and dome light dmlsanta Electrical Tech 7 04-10-2011 07:43 PM
Dome Light Bighomedog11 Interior Tech 21 01-28-2011 11:13 AM
Dome light RANGER @ GT Interior Parts 2 08-30-2009 12:56 AM
No power to my dome light Buddythetruck Interior Tech 7 07-08-2009 10:07 PM