Ford Ranger Forum - Forums for Ford Ranger enthusiasts!

Go Back   Ford Ranger Forum - Forums for Ford Ranger enthusiasts! > >
Forgot Password? Join Us!

Welcome to Ford Ranger Forum

Reply
 
Thread Tools Search this Thread

  #1  
Old 07-08-2019, 10:41 PM
rogerranger2122 rogerranger2122 is offline
Like the Forums
 
Join Date: Jul 2016
Posts: 45
Default Only 1 of 2 bolts holding Alternator...

2006 Honda pilot (sorry I know this is a ford forum but hoping for some insight anyway, not my car.).

I have a 20" breaker bar that couldn't even budge the OEM torque so I tapped it with a hammer and they came out. They were surprisingly tight compared to things I've removed on my ford ranger (which is plagued with rust and seized bolts etc). The Pilot has cables and hoses in the way of the 2 bolts that hold the alternator and I could only get about 1/8 turn before I had to remove the socket and breaker bar and reposition it (plus I had to pull the socket off and rotate it because it was a 6-point and wouldn't line up).

I had the new alternator installed and just needed to tighten down the 2 main bolts using the 20" breaker bar. Since it was such a short travel of the breaker bar (1/8th turn) I couldn't really get a feel for how tight the bolts were, but they certainly didn't feel nearly as tight as the OEM installation so I kept on tightening them - then one cracked. I nearly flipped when I realized there's probably no clearance to drill out the remaining cracked bolt in order to get an extractor bit on it and even if I did it would be a nightmare of an angle - was thinking it would need to be towed to shop and have engine hoisted and bolt extracted.

But I think it's fine, do you? :::
The bottom bolt is installed fine as it should be, it's the upper bolt that cracked.
As shown in picture, there's a small gap RED LINE between the alternator's bracket (BLUE CIRCLE) and I don't know what the other part is called on the left of the red line. The alternator is the YELLOW STAR.
Basically when the serpentine belt is installed and car is running, the alternator hinges towards the red line because of the pressure, BUT now it's simply being held by the part on the left of the red line. That part is metal even though it has a black plastic cover. So now the alternator can not just pivot/hinge back because this part is thankfully right there. The gap in the red line is only about 1/4" when installed without a cracked bolt but now the alternator is hinged back about only 1/4", so I think it's fine.

Here's the video I took this screenshot from if needed. Thanks




I mean, I would like to remove the cracked bolt but that doesn't seem practical.

Luckily the bolt that cracked is the one that connects the bracket (BLUE CIRCLE) to the frame. So, as mentioned the plate which is holding the alternator is pressing forward and being held in place by the part on the left of the red line. The bolt that connects the alternator to that bracket is not broke.

I really lucked out that that part is there on the left of the red line.
Attached Images
File Type: jpg alternator.jpg (90.0 KB, 8 views)

Last edited by rogerranger2122; 07-09-2019 at 01:44 AM.
Reply With Quote
  #2  
Old 07-09-2019, 08:24 AM
Dirtman Dirtman is offline
Banned
 
Join Date: Jul 2018
Posts: 516
Default Re: Only 1 of 2 bolts holding Alternator...

You don't tighten bolts with a breaker bar... and now you know why.
Reply With Quote
  #3  
Old 07-09-2019, 10:25 AM
rogerranger2122 rogerranger2122 is offline
Like the Forums
 
Join Date: Jul 2016
Posts: 45
Default Re: Only 1 of 2 bolts holding Alternator...

it's too far down to reach with a regular ratchet. I just recently bought this 20" breaker bar, normally I would have used a ratchet with a pipe over it to reach this but that's awkward and could break the ratchet considering how tight they were.

Forgot to mention though, yes the correct way would have been a ratchet with a foot pounds limiter set, which I could have borrowed I just found out, but anyway I'm not worried about the overall alternator situation though so it's all good.
Reply With Quote
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search


Similar Threads
Thread Thread Starter Forum Replies Last Post
how is my radiator even holding any fluid at all?? rogerranger2122 4.0 SOHC / 4.0 OHV Tech 6 05-08-2019 05:16 PM
How many bolts are holding the upper/lower intake together? 94mtx 4-Cylinder Tech 3 07-21-2015 07:46 AM
Rear bolts holding '93 driver seat austsinrick Interior Tech 1 10-21-2013 04:19 PM
For Sale: alternator bracket bolts John moore Engine & Drivetrain Parts 0 08-19-2013 01:33 PM
How many bolts are holding on your bed? zx6rrdan Exterior Tech 18 05-18-2011 12:33 PM