|
|
|
|
05-27-2010, 08:17 AM
|
|
Beefcaaaaakkee!!
|
|
Join Date: May 2010
Posts: 434
|
|
Catalytic converter is shot, what are my options?
My truck is at the shop right now, it was running a code for a bad catalytic converter on bank 2 (if I remember correctly) I changed out the 02 sensors, and checked the fuses, to narrow down all possibilities. I just got a call stating that it is indeed a bad catalytic converter and that they recommend changing out the entire Y pipe, which will cost $1,200 because they have to get OEM parts. Apparently they had tried this once before on the same year truck using after market cats and they could not get the check engine code turn off. They believe it was because the after market parts didn't have enough platinum in there.
This is a reputable shop and I believe them, so I'm wondering if there is any other route that you guys have gone in order to fix this problem. My truck is overdue for state inspection and I need to have a full history on my OBD; in other words, I cannot just clear my codes and then go in.
__________________
2004 Ford Ranger Edge manual 4.0 4x4 with 3" Body lift, 33x12.5 BFG A/T KO's, on Eagle Alloy 057 rims, and alot of mods
2011 Ford Mustang GT 5.0 manual with Flowmaster American Thunder exhaust
2005 Ford F250 automatic 5.4 4x4 with no mods
|
|
|
|
Register and never see these ads again. |
|
05-27-2010, 08:59 AM
|
|
THE COMPLAINT DEPARTMENT
|
|
Join Date: Nov 2009
Posts: 3,962
|
|
Re: Catalytic converter is shot, what are my options?
i was going to recommend a tune, headers and full exhaust since you're looking at having to spend the $ either way.. until i read state inspection.
Ive learned my lesson dicking around with these sensitive sissy ass trucks, they only like FOMOCO parts. From oil filters to slave cylinders. Hub bearings to spark plugs. They're picky. And since you have to pass inspection.. Might as well have it done right.
__________________
2001 Ford Ranger Supercab (4dr), Oxford White, 4.0 Sohc, 4x4, Manual trans (hurst equipped), 4:10's, 3" body lift.
Quote:
Originally Posted by Demon-FX4
The Edgeman sees his prey and strikes out from the darkness.
|
Quote:
Originally Posted by Rango88
Dont f+ck with Ch+ck
|
|
05-27-2010, 09:05 AM
|
|
Beefcaaaaakkee!!
|
|
Join Date: May 2010
Posts: 434
|
|
Re: Catalytic converter is shot, what are my options?
Yeah, state inspection is just one of the many things that I can't stand about New Jersey. I already have a tuner, which is probably why I never realized the check engine light until last month when I returned the truck to stock. There's someone over on R-F that wrecked his truck a while ago, we're trying to figure out how much shipping would be to see if I could use his old Y-pipe with 130k miles on it.
__________________
2004 Ford Ranger Edge manual 4.0 4x4 with 3" Body lift, 33x12.5 BFG A/T KO's, on Eagle Alloy 057 rims, and alot of mods
2011 Ford Mustang GT 5.0 manual with Flowmaster American Thunder exhaust
2005 Ford F250 automatic 5.4 4x4 with no mods
|
05-27-2010, 10:41 AM
|
|
Is today the day?
|
|
Join Date: Feb 2010
Posts: 254
|
|
Re: Catalytic converter is shot, what are my options?
Your best/cheapest option would be to get a high flow cat from someplace like Summit. They are universal and can be easily welded in with a 110v mig welder.
__________________
"The strongest reason for the people to retain the right to keep and bear arms is, as a last resort, to protect themselves against tyranny in government." - Thomas Jefferson -
Support Our Troops!
|
05-27-2010, 11:03 AM
|
|
Ford Tough
|
|
Join Date: Jan 2010
Posts: 412
|
|
Re: Catalytic converter is shot, what are my options?
"Universal" Cats are hit and miss...they will work sometimes but other times they won't. It all depends on the placing of the "honeycomb" inside of it. If they deal with mufflers, i would think that they could maybe get it from someone else, but alot of fords aren't made by anybody else. And as far as replacing the whole Y-Pipe, that is the only way you can buy them, I believe. The only other way would be to buy them by the side, but idk if they make them that way....and as far as buying the used one, make sure that the seller tapes up the ends of the pipe as soon as it comes off of the truck, b/c I've seen plenty of times where it doesn't seem to sound/work right after being exposed to outside air for too long. Sorry for the novel, just trying to help lol
|
05-27-2010, 11:30 AM
|
|
Beefcaaaaakkee!!
|
|
Join Date: May 2010
Posts: 434
|
|
Re: Catalytic converter is shot, what are my options?
Maurice, I'd go that route, but like I said in my original post and what SPless has just posted, I don't want to take the chance of it not working. This is all for state inspection, otherwise I'd just run it as is with my tuner.
SPless, can you elaborate on the not working right if it wasn't taped up? I know that he's had it apart, because he's going to check on a shipping price for me tomorrow. I do not know if it has been taped up or not, but I will ask.
__________________
2004 Ford Ranger Edge manual 4.0 4x4 with 3" Body lift, 33x12.5 BFG A/T KO's, on Eagle Alloy 057 rims, and alot of mods
2011 Ford Mustang GT 5.0 manual with Flowmaster American Thunder exhaust
2005 Ford F250 automatic 5.4 4x4 with no mods
|
05-27-2010, 11:31 AM
|
|
Is today the day?
|
|
Join Date: Feb 2010
Posts: 254
|
|
Re: Catalytic converter is shot, what are my options?
If you go with a Dynomax universal high flow cat, they are emission compliant. There is no way they could fail your truck in inspection.
__________________
"The strongest reason for the people to retain the right to keep and bear arms is, as a last resort, to protect themselves against tyranny in government." - Thomas Jefferson -
Support Our Troops!
|
05-27-2010, 04:28 PM
|
|
Ford Tough
|
|
Join Date: Jan 2010
Posts: 412
|
|
Re: Catalytic converter is shot, what are my options?
Well, idk if it would affect much with the catalyst, but my dad cut a muffler off a newer ranger, and it laid around for about a week before he put it on his truck, and it had a weird tone to it...to my knowledge I don't know about it affecting anything really, I've just heard rumors about it and figure its better safe than sorry. I know I said I've seen it happen before, sorry about that...pretty much all I've seen was with mufflers. Also, I would tape them up anyways to keep small animals out of them.
|
05-27-2010, 04:34 PM
|
|
Ford Motor Co
|
|
Join Date: Feb 2010
Posts: 170
|
|
Re: Catalytic converter is shot, what are my options?
your truck should have 3-4 cats
the y-pipe has 2 (one one each side as a "pre-cat) and one main one before the muffler, that may or may not be 2 cats as well
the y-pipe cats do not make enough of a difference to cause a check engine light. The rear o2 sensor that measures cat efficiency is only reading that MAIN cat. You can easily eliminate the other 2 one the ypipe with any codes.
The front mount o2 sensors monitor air-fuel ratio, the rear monitors the cat efficiency, so for them to say you have a bank 2 cat code is a little of a stretch
__________________
2004 Explorer Sport Trac XLT premium 4.0L auto 4wd
1995 Ranger XLT ext cab 3.0L auto 2wd
2005 Jeep Liberty Limited 3.7L auto 4wd
2001 Ranger XLT reg cab 2.3L auto 2wd--SOLD
1999 Ranger XLT reg cab 2.5L manual 2wd--SOLD
|
|
|
|
05-28-2010, 06:02 AM
|
|
Beefcaaaaakkee!!
|
|
Join Date: May 2010
Posts: 434
|
|
Re: Catalytic converter is shot, what are my options?
Quote:
Originally Posted by Scottg
your truck should have 3-4 cats
the y-pipe has 2 (one one each side as a "pre-cat) and one main one before the muffler, that may or may not be 2 cats as well
the y-pipe cats do not make enough of a difference to cause a check engine light. The rear o2 sensor that measures cat efficiency is only reading that MAIN cat. You can easily eliminate the other 2 one the ypipe with any codes.
The front mount o2 sensors monitor air-fuel ratio, the rear monitors the cat efficiency, so for them to say you have a bank 2 cat code is a little of a stretch
|
Scott, I read the code before bringing the truck into them, it's a P0430, which does effect the cat. I looked it up online and went through all of the possible causes, but it didn't work, the only thing left is the cat.
I remember when I was researching tuners that it stated your cats might burn out quicker and I think that's what may have happened. I've been running one now for 5 - 6 years.
I got them to knock 5% off the price which helps a little bit, they're ordering the part today.
__________________
2004 Ford Ranger Edge manual 4.0 4x4 with 3" Body lift, 33x12.5 BFG A/T KO's, on Eagle Alloy 057 rims, and alot of mods
2011 Ford Mustang GT 5.0 manual with Flowmaster American Thunder exhaust
2005 Ford F250 automatic 5.4 4x4 with no mods
|
|
|
|
|
|
|
05-28-2010, 08:12 PM
|
Custom KeyChain R Me
|
|
Join Date: Feb 2009
Posts: 718
|
|
Re: Catalytic converter is shot, what are my options?
Quote:
Originally Posted by Scottg
your truck should have 3-4 cats
the y-pipe has 2 (one one each side as a "pre-cat) and one main one before the muffler, that may or may not be 2 cats as well
the y-pipe cats do not make enough of a difference to cause a check engine light. The rear o2 sensor that measures cat efficiency is only reading that MAIN cat. You can easily eliminate the other 2 one the ypipe with any codes.
The front mount o2 sensors monitor air-fuel ratio, the rear monitors the cat efficiency, so for them to say you have a bank 2 cat code is a little of a stretch
|
yes yes and yes
__________________
Quote:
Originally Posted by redrumedge
98blown you should be an MD! that's the same stuff my doc asks and ur spot on man!!!
|
98 4.0 2wd-----supercharger fully build heads cam...all show with go......3 time world of wheels champ 5 time national winner
lots of ranger parts for sale leftovers from my 94/96
96 sitting on the frame, waiting to go lower
custom billet parts by me intake adapters and billet steps for the step sides
please sign my guestbook!!
http://breyperformancemachine.shutterfly.com/
|
|
|
|
|
|
|
05-30-2010, 07:29 AM
|
|
Ford Motor Co
|
|
Join Date: Feb 2010
Posts: 170
|
|
Re: Catalytic converter is shot, what are my options?
Quote:
Originally Posted by winks
Scott, I read the code before bringing the truck into them, it's a P0430, which does effect the cat. I looked it up online and went through all of the possible causes, but it didn't work, the only thing left is the cat.
I remember when I was researching tuners that it stated your cats might burn out quicker and I think that's what may have happened. I've been running one now for 5 - 6 years.
I got them to knock 5% off the price which helps a little bit, they're ordering the part today.
|
Winks, what I am saying is, there's no way for them to know which cat is bad by just pulling a code. The ypipe cats are not big enough to throw a code on their own, only the Main cat can do that. Also for them to pin-point a 1 sided cat code on a ranger is impossible, because there is no code that says that for ranger-explorers
__________________
2004 Explorer Sport Trac XLT premium 4.0L auto 4wd
1995 Ranger XLT ext cab 3.0L auto 2wd
2005 Jeep Liberty Limited 3.7L auto 4wd
2001 Ranger XLT reg cab 2.3L auto 2wd--SOLD
1999 Ranger XLT reg cab 2.5L manual 2wd--SOLD
|
|
|
|
06-01-2010, 05:58 AM
|
|
Beefcaaaaakkee!!
|
|
Join Date: May 2010
Posts: 434
|
|
Re: Catalytic converter is shot, what are my options?
I understand what you're staying now Scott.
In the end, I just said screw it and told them to throw on a new Y pipe from Ford. I need this thing to pass state inspection ASAP. Hopefully I'll be able to make a bit back on taking my old cats to the scrap yard.
__________________
2004 Ford Ranger Edge manual 4.0 4x4 with 3" Body lift, 33x12.5 BFG A/T KO's, on Eagle Alloy 057 rims, and alot of mods
2011 Ford Mustang GT 5.0 manual with Flowmaster American Thunder exhaust
2005 Ford F250 automatic 5.4 4x4 with no mods
|
02-28-2015, 01:33 PM
|
|
Ranger commuter
|
|
Join Date: May 2010
Posts: 464
|
|
Re: Catalytic converter is shot, what are my options?
Quote:
Originally Posted by winks
I understand what you're staying now Scott.
In the end, I just said screw it and told them to throw on a new Y pipe from Ford. I need this thing to pass state inspection ASAP. Hopefully I'll be able to make a bit back on taking my old cats to the scrap yard.
|
What did that cost you? I have a leak coming from the y-pipe/passenger manifold I can't seem to fix.
Ford just quoted me $2400 my cost for the y-pipe
__________________
04 Supercab 4dr 4.0 5spd 4x4 EDGE. Daily Driver
96 F350 Crewcab 460 5spd Vortech S/C 4X4 6" 35s
94 Lightning Bassani headers back CAI Underdrive Pulleys
86 F250 Reg Cab 6.9 4Spd 4x4 6" 35s (powerstoke,D60 5spd on the way)
80 F350 Reg Cab 429 C6 4x4 L&L headers F450 rear springs All Out Pulling Truck(D60 Laddered Frame, 540cid coming)
|
02-28-2015, 04:28 PM
|
|
Mr H....A....P...P....Y👿
|
|
Join Date: Nov 2012
Posts: 2,911
|
|
Re: Catalytic converter is shot, what are my options?
__________________
2014 F150 xl 3.7 6 speed auto.
Quote:
Originally Posted by pk9298
HELL TO THE NO!! Abort abort abort!! That's the first thing to go!!! Ewwwww! I'm not no vampire! I don't enjoy red tea
|
|
|
|