I was wondering if anybody has run a wire through/behind the taillight into the cab. I'm trying to figure out where to run my CB antenna wire and some off road lights.

If you have any other ideas about where to run exterior wires let me know, pics would be the bomb!

__________________
[FONT="Fixedsys"]2001 Ford Ranger Edge
Nerf Bars
12" JL W1
JL V2 Slash class D amp
Kenwood Head Unit
Cobra CB Radio/ W PA
Cobra Radar Detector (Cord hidden
in the roof)
HID Headlights + LED Eyebrows
And of course my NRA sticker and CSA Battle Flag
5% Window Tint[/FONT]

Pull up ur carpet or vinyl flooring and remove one of the floor plugs.

U run it through the light on the cab u risk it leaking water

__________________

not sure wear ur puting ur cb antenna? but mine is right behind my cab, i havent wired it yet but ive seen friends wire it straight through the cab. not sure how they do it though. you could run the wires under the side lip of the bed.

I ran my CB coax through a grommet in the firewall. I removed the fuse box under the hood and there is a boot/plug thing with a bunch of wires going through it. I cut a hole in that (be careful as you do not want to cut any of the wiring going through there) and ran my coax through that. Also have wires for my offroad lights, CB power and PA wires going through it.

__________________
Sold:2004 XLT 4x2 Ext. Cab. 3.0 Mods: 3" spindle, AAL, shackle, 32x11.5 on 15x8s, billet grille, clear corners, flow 40 dumped, line-x, CB/PA, traction bars, lil sound system, auto up down windows
Sold:2005 XLT 4x4 Ext. Cab. 4.0 Mods: ProComp lights w/ HID swap on tabs, 32x11.5 on 15x8s, CB/PA, black out heads/corners, lil sound system, cranked t-bars, flow 40 dumped, line-x, shell, bed rug, 06+ tails, metal tail gate handle since plastic one shattered, OHC, Mustang Dome.

Where on the floor are they located at?

__________________
[FONT="Fixedsys"]2001 Ford Ranger Edge
Nerf Bars
12" JL W1
JL V2 Slash class D amp
Kenwood Head Unit
Cobra CB Radio/ W PA
Cobra Radar Detector (Cord hidden
in the roof)
HID Headlights + LED Eyebrows
And of course my NRA sticker and CSA Battle Flag
5% Window Tint[/FONT]

U got 2 in the front on each side. pull up the flooring at the driver foot are. u will see a oval rubber plug.

Behind ur seats pull up the flooring and u will see 2 more unless you have a extended cab with jump seats. you will need to remove those to get access.

__________________

pull up the sill and carpet on either side (passenger or driver) and you will see 2 round, black, rubber plugs in the floor. i made an "X" cut in one of mine and brought the wires in there. after i got them in , i used black Permatex on the plug to reseal it, then put the carpet and sill back.

__________________

1983 Ranger, reg cab, short bed, 2.8, 5 spd, 4.56's, 2" bl, 215/85-16 Treadwright AT's

Here is a picture of the driver side plug

__________________

I might give it a try.

__________________
[FONT="Fixedsys"]2001 Ford Ranger Edge
Nerf Bars
12" JL W1
JL V2 Slash class D amp
Kenwood Head Unit
Cobra CB Radio/ W PA
Cobra Radar Detector (Cord hidden
in the roof)
HID Headlights + LED Eyebrows
And of course my NRA sticker and CSA Battle Flag
5% Window Tint[/FONT]

Do the 2009 Ranger sport extended cab have those floor plugs ? Thanks.

i just got 2 firestik whips and mounts when i got my toolbox but would 1 93 xlt have those rubber plugs on the floor?

2009 Sport has a rubber plug behind the passenger seat. That's where I ran my coax.

__________________
"If you can't go hard, go home"