Ford Ranger Forum - Forums for Ford Ranger enthusiasts!

Go Back   Ford Ranger Forum - Forums for Ford Ranger enthusiasts! > >
Forgot Password? Join Us!

Welcome to Ford Ranger Forum

Reply
 
Thread Tools Search this Thread

  #16  
Old 04-17-2011, 02:35 PM
4six0 4six0 is offline
Learning to use the forums
 
Join Date: Apr 2011
Posts: 14
Default Re: 2.9 4.0?

Ok would any body know the measurements on the four or two nine like water pump to back top to bottom and the width?
Reply With Quote
  #17  
Old 04-17-2011, 02:40 PM
Jimmeh Jimmeh is offline
I am THE Hank Hill.
 
Join Date: Sep 2009
Posts: 1,085
Send a message via AIM to Jimmeh
Default Re: 2.9 4.0?

Quote:
Originally Posted by 4six0 View Post
Ok would any body know the measurements on the four or two nine like water pump to back top to bottom and the width?
Oh boy....

If somebody can't get you the measurements, I'll bundle up and go take some for ya by the end of the week. I'm putting mine back together next weekend anyway, but I don't know them off the top of my head and it's snowing/raining right now. I might even start tomorrow depending on my work schedule.
__________________
92 Ford Ranger Supercab XLT 4X4.
Not a ton done to it, but it's nowhere near finished
05 Chevy Silverado 1500 W/T 4X4
Way too much done to list and it's also not even close to done

"The only woman I'm pimping from now on is Sweet Lady Propane. And I'm tricking her out all over this town."
Reply With Quote
  #18  
Old 04-17-2011, 02:40 PM
4six0 4six0 is offline
Learning to use the forums
 
Join Date: Apr 2011
Posts: 14
Default Re: 2.9 4.0?

Ok where would a find all the measurements for both engines
Reply With Quote
  #19  
Old 04-17-2011, 02:41 PM
Jimmeh Jimmeh is offline
I am THE Hank Hill.
 
Join Date: Sep 2009
Posts: 1,085
Send a message via AIM to Jimmeh
Default Re: 2.9 4.0?

I tried searching for ya a little on some of the Ranger boards, but I couldn't find any. You can try a general Google search, but not sure if you would dig anything up with that.
__________________
92 Ford Ranger Supercab XLT 4X4.
Not a ton done to it, but it's nowhere near finished
05 Chevy Silverado 1500 W/T 4X4
Way too much done to list and it's also not even close to done

"The only woman I'm pimping from now on is Sweet Lady Propane. And I'm tricking her out all over this town."
Reply With Quote
  #20  
Old 04-17-2011, 02:41 PM
DiabloBlanco DiabloBlanco is offline
Get Lifted.
 
Join Date: Nov 2010
Posts: 6,402
Default Re: 2.9 4.0?

2.9 Specifications

Engine Family Cologne
Engine Displacement (Cubic Inches) 177
Cylinders 6
Arrangement of Cylinders "V" Shape
Bore x Stroke 3.66 x 2.83
Compression Ratio 9.0:1
Valvetrain Pushrod Overhead Valve
Fuel System MPFI (Multiport Electronic Fuel Injection)
Fuel Pressure 30-40psi
Horsepower 140hp @ 4600rpm
Torque 170hp @ 2600rpm
Oil Pressure 20psi @ warm Idle 55psi @ 2000rpm
Tune Up

Spark Plug AWSF-42C
Spark Plug Gap 0.044
Ignition Timing 10 degrees BTDC
Firing Order 1-4-2-5-3-6
Distributor Rotation Clockwise
Capacities

Oil Capacity With Filter Change 5.0 quarts
Oil Capacity Without Filter Change 4.0 quarts
Cooling System Capacity (Quarts) W/AC- 7.2 / W/O AC 7.8
Torque Specifications

Cylinder Head Torque in 3 steps [1st (22ft-lbs), 2nd (51-55ft-lbs), 3rd (Turn 90 degrees)]
Main Bearing Bolts 65-75ft-lbs
Rod Bearing Bolts 19-24ft-lbs
Crankshaft Pulley Bolts 85-96ft-lbs
Flywheel to Crankshaft Bolts 47-52ft-lbs
Intake Manifold 15-18 ft-lbs [5-steps (hand start & snug) (3-6) (6-11) (11-15) (15-18) (Repeat 15-18 after warm up)]
Exhaust Manifold 20-30ft-lbs
Valve Specifications

Seat Angle Degree 45
Face Angle Degree 44
Spring Test Pressure 143lbs @ 1.22in
Spring Installed Height 1.58-1.61in
Stem to Guide Clearance Intake 0.0008-0.0025in
Stem to Guide Clearance Exhaust 0.0018-0.0035in
Stem Diameter Intake 0.3159-0.3167in
Stem Diameter Exhaust 0.3149-0.3156in
Crankshaft Specifications

Main Bearing Journal Diameter 2.2433-2.2441in
Main Bearing Oil Clearance 0.0008-0.0015in
Shaft End-Play 0.004-0.008
Thrust on No. 3
Connecting Rod Specifications

Journal Diameter 2.1252-2.1260in
Oil Clearance 0.0006-0.0016in
Side Clearance 0.004-0.011in
Piston & Ring Specifications

Piston to Bore Clearance 0.0011-0.0019in
Ring Side Clearance Top Compression 0.0020-0.0033in
Ring Side Clearance Bottom Compression 0.0020-0.0033in
Ring Side Clearance Oil Control Snug
Ring Gap Top Compression 0.015-0.023in
Ring Gap Bottom Compression 0.015-0.023in
Ring Gap Oil Control 0.015-0.023in
__________________
YZ the way to be!
The Brotherhood!

Mods to come: Camburg entry 6.0 system. FiberwerkX Fenders and bedsides. Tube bumper.
R.I.P. Jeff Ashton. 1992-2011
Reply With Quote
  #21  
Old 04-17-2011, 02:42 PM
4six0 4six0 is offline
Learning to use the forums
 
Join Date: Apr 2011
Posts: 14
Default Re: 2.9 4.0?

Oh ok thanks guys it s snowing here now with the sun out sure it ll rain some time today lol
Reply With Quote
  #22  
Old 04-17-2011, 02:42 PM
DiabloBlanco DiabloBlanco is offline
Get Lifted.
 
Join Date: Nov 2010
Posts: 6,402
Default Re: 2.9 4.0?

4.0 specs


Specifications

Engine Displacement (Cubic Inches) 245 CID
Type OHV (1990 - 2000) (VIN Code X)
SOHC (2001 - 2007) (VIN Code E)

Bore x Stroke 3.95 x 3.31 inches
Compression Ratio 9.0:1
Fuel System Sequential Fuel Injection
Fuel Pressure 39 - 40 PSI (30 PSI @ idle) (OHV Engines)
64 - 75 PSI (SOHC Engines)

Horsepower 160hp @ 4200 RPM (1990 - 2000)
207hp @ 5250 RPM (2001 - 2007)

Torque 220 @ 2400 RPM (1990 - 2000)
238 @ 3000 RPM (2001 - 2007)

Oil Pressure 40 - 60 PSI @ 2000 RPM


Spark Plug Gap 0.054 inches
Ignition Timing 10 degrees BTDC
Firing Order 1-4-2-5-3-6
Capacities

Oil Capacity With Filter Change 5 Quarts (OHV Engines)
5 Quarts (SOHC Engines)

Cooling System Capacity (Quarts) W/AC- 7.2 / W/O AC 6.5 (OHV Engines)
13.2 Quarts (SOHC Engines)

Torque Specifications

Cylinder Head Torque in 3 steps [1st (22-26ft-lbs), 2nd (52-56ft-lbs), 3rd (Tighten another 90-degrees)] (OHV Engines)
Torque in 2 steps [1st (24ft-lbs), 2nd (Tighten another 90-degrees)] (SOHC Engines)

Main Bearing Bolts 66 - 77 ft-lbs (OHV Engines)
72 ft-lbs (SOHC Engines)

Rod Bearing Bolts 19 - 24 ft-lbs (OHV Engines)
Torque in 2 steps [1st (15ft-lbs), 2nd (Tighten another 90-degrees)] (SOHC Engines)

Crankshaft Pulley Bolts Torque in 2 steps [1st (30-37ft-lbs), 2nd (Tighten another 90-degrees)] (OHV Engines)
Torque in 2 steps [1st (37ft-lbs), 2nd (Tighten another 90-degrees)] (SOHC Engines)

Flywheel to Crankshaft Bolts 59 ft-lbs (OHV Engines)
75 - 85 ft-lbs (SOHC Engines)

Lower Intake Manifold / Throttle Body Torque in 4 steps [1st (3-6ft-lbs), 2nd (6-11ft-lbs), 3rd (11-15ft-lbs) 4th (15-18ft-lbs)] (OHV Engines)
7 ft-lbs (SOHC Engines)

Exhaust Manifold 19 ft-lbs (OHV Engines)
16 ft-lbs (SOHC Engines)
__________________
YZ the way to be!
The Brotherhood!

Mods to come: Camburg entry 6.0 system. FiberwerkX Fenders and bedsides. Tube bumper.
R.I.P. Jeff Ashton. 1992-2011
Reply With Quote
  #23  
Old 04-17-2011, 02:43 PM
Jimmeh Jimmeh is offline
I am THE Hank Hill.
 
Join Date: Sep 2009
Posts: 1,085
Send a message via AIM to Jimmeh
Default Re: 2.9 4.0?

That doesn't have the actual dimensions of the engine. Guessing you got that from TRS cause I was looking at the same thing, lol.
__________________
92 Ford Ranger Supercab XLT 4X4.
Not a ton done to it, but it's nowhere near finished
05 Chevy Silverado 1500 W/T 4X4
Way too much done to list and it's also not even close to done

"The only woman I'm pimping from now on is Sweet Lady Propane. And I'm tricking her out all over this town."
Reply With Quote
  #24  
Old 04-17-2011, 02:45 PM
4six0 4six0 is offline
Learning to use the forums
 
Join Date: Apr 2011
Posts: 14
Default Re: 2.9 4.0?

Lol helped me a bit
Reply With Quote
  #25  
Old 04-17-2011, 02:47 PM
DiabloBlanco DiabloBlanco is offline
Get Lifted.
 
Join Date: Nov 2010
Posts: 6,402
Default Re: 2.9 4.0?

Yeah Just thought it would help him. lol maybe.

----------

Looky

overall length flywheel to front pulley face 23.5" ; overall height, stock oil pan to top of carb, not counting air filter 26", overall width of pulleys (A/C to alternator) 30". Overall block width outside edge of valve cover to outside edge of the other cover 23" or so
__________________
YZ the way to be!
The Brotherhood!

Mods to come: Camburg entry 6.0 system. FiberwerkX Fenders and bedsides. Tube bumper.
R.I.P. Jeff Ashton. 1992-2011
Reply With Quote
  #26  
Old 04-17-2011, 02:50 PM
4six0 4six0 is offline
Learning to use the forums
 
Join Date: Apr 2011
Posts: 14
Default Re: 2.9 4.0?

That's for the 2.9 right
Reply With Quote
  #27  
Old 04-17-2011, 02:51 PM
DiabloBlanco DiabloBlanco is offline
Get Lifted.
 
Join Date: Nov 2010
Posts: 6,402
Default Re: 2.9 4.0?

yes

----------

but those are approximates.
__________________
YZ the way to be!
The Brotherhood!

Mods to come: Camburg entry 6.0 system. FiberwerkX Fenders and bedsides. Tube bumper.
R.I.P. Jeff Ashton. 1992-2011
Reply With Quote
  #28  
Old 04-17-2011, 02:52 PM
4six0 4six0 is offline
Learning to use the forums
 
Join Date: Apr 2011
Posts: 14
Default Re: 2.9 4.0?

Sweet thanks

----------

Alright
Reply With Quote
  #29  
Old 04-17-2011, 03:18 PM
Jimmeh Jimmeh is offline
I am THE Hank Hill.
 
Join Date: Sep 2009
Posts: 1,085
Send a message via AIM to Jimmeh
Default Re: 2.9 4.0?

Quote:
Originally Posted by DiabloBlanco View Post
yes

----------

but those are approximates.
Where did you get those from?
__________________
92 Ford Ranger Supercab XLT 4X4.
Not a ton done to it, but it's nowhere near finished
05 Chevy Silverado 1500 W/T 4X4
Way too much done to list and it's also not even close to done

"The only woman I'm pimping from now on is Sweet Lady Propane. And I'm tricking her out all over this town."
Reply With Quote
  #30  
Old 04-17-2011, 03:23 PM
DiabloBlanco DiabloBlanco is offline
Get Lifted.
 
Join Date: Nov 2010
Posts: 6,402
Default Re: 2.9 4.0?

I dont really rmember google search
__________________
YZ the way to be!
The Brotherhood!

Mods to come: Camburg entry 6.0 system. FiberwerkX Fenders and bedsides. Tube bumper.
R.I.P. Jeff Ashton. 1992-2011
Reply With Quote
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search