|
12-14-2014, 10:20 AM
|
|
Ford Tough
|
|
Join Date: Feb 2014
Posts: 231
|
|
That's a sweet looking design! Built this one my self cut and welded and sprayed all within 24 hours it was on my truck
__________________
2008 xlt 4x4 extended cab, 4.0 SOHC,automatic
|
Register and never see these ads again. |
|
12-14-2014, 01:53 PM
|
|
Ford Truck Driver
|
|
Join Date: Mar 2014
Posts: 80
|
|
Quote:
Originally Posted by 4.0beast
That's a sweet looking design! Built this one my self cut and welded and sprayed all within 24 hours it was on my truck
|
Looks like you could go through a brick wall and keep going with the one you have !!XD hahah
__________________
2003 Ford Ranger edge v6
|
12-14-2014, 02:55 PM
|
|
Ford Tough
|
|
Join Date: Feb 2014
Posts: 231
|
|
Quote:
Originally Posted by Ranger-Danger85
Looks like you could go through a brick wall and keep going with the one you have !!XD hahah
|
Haha pretty much it's al 1/4 inch plate and the bar is 2" OD with 1/4 wall heavy duty right here 15,000lbs d rings with triple pass welds on both sides I have hit 2 coyotes already and not a issue at all! Next project is making skid plates for the axles and transfercase she looks stock but it's built ford tough! I like the work you have done with your builds
__________________
2008 xlt 4x4 extended cab, 4.0 SOHC,automatic
|
12-14-2014, 02:58 PM
|
|
Ford Tough
|
|
Join Date: Feb 2014
Posts: 231
|
|
Also rear bumper all 1/4 inch plate with the same 15,000lbs d rings but I went over kill and they got 6 passes with mig on both sides and it's all braced so nothing bends when being pulled on
__________________
2008 xlt 4x4 extended cab, 4.0 SOHC,automatic
|
12-14-2014, 04:18 PM
|
|
Ford Truck Driver
|
|
Join Date: Mar 2014
Posts: 80
|
|
Quote:
Originally Posted by 4.0beast
Also rear bumper all 1/4 inch plate with the same 15,000lbs d rings but I went over kill and they got 6 passes with mig on both sides and it's all braced so nothing bends when being pulled on
|
DAMNNN you've got some bad ass bumpers ! I still need to order my d ring shackles and my 10" LED I'm going to use them in a fog light set up haha.
__________________
2003 Ford Ranger edge v6
|
12-14-2014, 06:57 PM
|
|
Ford Tough
|
|
Join Date: Feb 2014
Posts: 231
|
|
What brand of leds are you using? That will look sweet keep me posted on how it turns out can't wait to see it!
__________________
2008 xlt 4x4 extended cab, 4.0 SOHC,automatic
|
12-14-2014, 07:11 PM
|
|
Ford Ranger Driver
|
|
Join Date: Jun 2014
Posts: 988
|
|
Quote:
Originally Posted by 4.0beast
Also rear bumper all 1/4 inch plate with the same 15,000lbs d rings but I went over kill and they got 6 passes with mig on both sides and it's all braced so nothing bends when being pulled on
|
damn man. You wanna make me a back bumper
|
12-14-2014, 07:27 PM
|
|
Ford Tough
|
|
Join Date: Feb 2014
Posts: 231
|
|
Quote:
Originally Posted by JPs65 galaxie
damn man. You wanna make me a back bumper
|
I would but I'm in Canada shipping would be tons on a heavy bumper
__________________
2008 xlt 4x4 extended cab, 4.0 SOHC,automatic
|
12-14-2014, 07:40 PM
|
|
Ford Ranger Driver
|
|
Join Date: Jun 2014
Posts: 988
|
|
Quote:
Originally Posted by 4.0beast
I would but I'm in Canada shipping would be tons on a heavy bumper
|
true that haha. You have some sick bumpers though
|
12-14-2014, 08:50 PM
|
|
Ford Tough
|
|
Join Date: Feb 2014
Posts: 231
|
|
Quote:
Originally Posted by JPs65 galaxie
true that haha. You have some sick bumpers though
|
Thanks guys! These bumpers sure help I hit a coyote with my truck recently and I found about half of it good solid bumoers and I have had people rear end me in the parking lot and all I have to do is while there paint of the Bedliner
__________________
2008 xlt 4x4 extended cab, 4.0 SOHC,automatic
|
12-15-2014, 06:11 AM
|
|
Useless olde guy
|
|
Join Date: Dec 2012
Posts: 3,228
|
|
Re: Custom bumpers
Good job to both you guys. How do you keep your D rings from rattling when your driving? The ones on my equipment trailer about drive me nuts.
__________________
'04 Edge, Scab/flareside, 2wd, 3.0, 5 speed, 4:10 open. Billet grille, Raceline Raptor black wheels, 265/75/16 DuraTracs. Tbar crank, AAL. Fox shocks, Thrush welded SI/DO swept back side exit. Morimoto projectors, '06 tails and power mirrors. LEDs all the way around. Blacked out fender badge. Access Limited rollup tonneau. 5% tint on back three windows. Airbox mod, FWIW. And a Border Collie that likes it too!!
|
12-15-2014, 06:15 AM
|
|
Ford Tough
|
|
Join Date: Feb 2014
Posts: 231
|
|
Quote:
Originally Posted by johnday
Good job to both you guys. How do you keep your D rings from rattling when your driving? The ones on my equipment trailer about drive me nuts.
|
My bumpers are sprayed with truck bed liner so that really dampens the noise before the paint it drove me crazy the rattling they did or ever red light they would make a noise but the bed liner takes away the metal on metal noise they are quiet it's very rare I hear them
__________________
2008 xlt 4x4 extended cab, 4.0 SOHC,automatic
|
12-15-2014, 07:42 AM
|
|
No wire hangers, ever!
|
|
Join Date: Jun 2010
Posts: 10,362
|
|
Re: Custom bumpers
Quote:
Originally Posted by johnday
How do you keep your D rings from rattling when your driving? The ones on my equipment trailer about drive me nuts.
|
Couple Options:
#1 (Cheapest):
http://www.fordrangerforum.com/exter...isolators.html
#2:
http://www.amazon.com/Daystar-KU71074BK-D-Ring-Shackle-Washer/dp/B004IARSFI/ref=pd_sim_auto_1?ie=UTF8&refRID=0RVK4ZEM7MTH4P42B1GChttp://www.amazon.com/Daystar-KU70056BK-Black-D-Ring-Isolator/dp/B001P22UUU
Last edited by Logan03CO; 12-15-2014 at 07:48 AM.
|
01-08-2015, 03:22 PM
|
Learning to use the forums
|
|
Join Date: Jan 2015
Posts: 1
|
|
Re: Custom bumpers
Hi, I have a 1998 Ranger (StepSide). Did you ever made these? Any Pictures?
|
01-11-2015, 10:19 AM
|
|
Ford Tough
|
|
Join Date: Feb 2014
Posts: 231
|
|
Quote:
Originally Posted by mastersomraty
Hi, I have a 1998 Ranger (StepSide). Did you ever made these? Any Pictures?
|
Did I ever make what????
__________________
2008 xlt 4x4 extended cab, 4.0 SOHC,automatic
|
Thread Tools |
Search this Thread |
|
|
|
|