|
12-25-2010, 04:47 PM
|
|
truck ford shouda made!
|
|
Join Date: Dec 2010
Posts: 195
|
|
piaa lights wiring to inside of cab??
we got everything ready but we cant find a way to run the wire to the inside of the cab through the firewall to the inside of the truck. Anyone know??
__________________
Dark Shadow Gray
2011 FX2 Sport Ranger
4x2, 4.0 SOHC, 4 door Ext. cab, Jump seats removed, Lund vent visors, PIAA driving lights in the grill,
Blacked out headlights & corners, LED black tails, 1.25" T bar crank, 32X11.5x15 BFG All Terrain T/A KOs, 20% window tint all around plus windshield strip
|
Register and never see these ads again. |
|
12-25-2010, 04:58 PM
|
|
...............
|
|
Join Date: May 2009
Posts: 23,399
|
|
Re: piaa lights wiring to inside of cab??
Around the steering shaft there are some factory wires coming through. Run them through (notice picture I posted)
OR
Drill a hole in the firewall for this, remove the fuse box pictured and you will be able to see where you can safely drill a hole.
To drill the hole use a step drill bit, it will drill through it like butter. You can use tape or a marker to mark the bit so you know when to stop.
The hole is drilled, do not forget to use a rubber grommet. If you don't use one your wire will chafe and short. You can pick up a small box for a few bucks at a local hardware store.
__________________
2005 Edge
Last edited by STL; 12-25-2010 at 05:22 PM.
|
12-25-2010, 05:18 PM
|
Modding To Continue >>>>
|
|
Join Date: May 2009
Posts: 1,114
|
|
Re: piaa lights wiring to inside of cab??
Yes you are a good man STL for this, I was just thinking how I was going to do this. Thanks a bunch.
|
12-25-2010, 05:40 PM
|
|
truck ford shouda made!
|
|
Join Date: Dec 2010
Posts: 195
|
|
Re: piaa lights wiring to inside of cab??
Thanks STL!! We got that down now and just like finding wire to wire in with a hot wire that only works with the ignition on and possibly If it can be done only when the low beam is on .. suggestions cause we dont know?
__________________
Dark Shadow Gray
2011 FX2 Sport Ranger
4x2, 4.0 SOHC, 4 door Ext. cab, Jump seats removed, Lund vent visors, PIAA driving lights in the grill,
Blacked out headlights & corners, LED black tails, 1.25" T bar crank, 32X11.5x15 BFG All Terrain T/A KOs, 20% window tint all around plus windshield strip
|
12-25-2010, 05:57 PM
|
|
...............
|
|
Join Date: May 2009
Posts: 23,399
|
|
Re: piaa lights wiring to inside of cab??
__________________
2005 Edge
|
12-25-2010, 06:12 PM
|
|
truck ford shouda made!
|
|
Join Date: Dec 2010
Posts: 195
|
|
Re: piaa lights wiring to inside of cab??
you rock STL!! Thanks so much!
----------
Ok read that and so did my dad.. the PIAAs arnt set up like that. Everything is hooked up right except for one wire has to go to a hot wire that is only hot when the switch is on. He doesnt want to go under the dash.. he'd like to tie them in to the low beam on the headlights but doesnt know what wire. Any idea?
__________________
Dark Shadow Gray
2011 FX2 Sport Ranger
4x2, 4.0 SOHC, 4 door Ext. cab, Jump seats removed, Lund vent visors, PIAA driving lights in the grill,
Blacked out headlights & corners, LED black tails, 1.25" T bar crank, 32X11.5x15 BFG All Terrain T/A KOs, 20% window tint all around plus windshield strip
|
12-25-2010, 06:21 PM
|
|
...............
|
|
Join Date: May 2009
Posts: 23,399
|
|
Re: piaa lights wiring to inside of cab??
Not sure if this will help
http://www.fordrangerforum.com/exter...ht-wiring.html<===CLICK
Only wire I can think of would be the radio power wire as it is switched when the truck is turned on.
__________________
2005 Edge
|
12-25-2010, 07:37 PM
|
|
Do not touch the trim!
|
|
Join Date: Aug 2010
Posts: 3,022
|
|
Re: piaa lights wiring to inside of cab??
X1,000 on the rubber grommet for the wire thru the firewall... unless you can slip the wire in with another OEM grommet or make a little X cut in a rubber plug & push the wire through it & seal it with silicone.
If you can't find one (or a big pkg) locally for $1 or less let me know, I have a bunch of grommets in all sizes.
__________________
'96 XLT, 4.0L, 4x4 Auto, Super Cab, K&N Filter, Dual Exhaust, 200a Alt, Clear Corners, BUGGMAN LED's, Expo Power Seats & Console, LED modded '01 Tails
Need LED's? Send me a PM
LINKS... Click 'em - - -> BUGGMAN PICS - - -BUGGMAN'S YouTube Channel - - -BUGGMAN'S FaceBook
|
12-25-2010, 10:50 PM
|
|
truck ford shouda made!
|
|
Join Date: Dec 2010
Posts: 195
|
|
Re: piaa lights wiring to inside of cab??
we got em! Dad managed to cut some of the rubber away then file a small gap into the plastic around it so it could slide through. Thank you for the help guys we would still be out there without it!
__________________
Dark Shadow Gray
2011 FX2 Sport Ranger
4x2, 4.0 SOHC, 4 door Ext. cab, Jump seats removed, Lund vent visors, PIAA driving lights in the grill,
Blacked out headlights & corners, LED black tails, 1.25" T bar crank, 32X11.5x15 BFG All Terrain T/A KOs, 20% window tint all around plus windshield strip
|
12-25-2010, 10:54 PM
|
|
Ford Ranger Driver
|
|
Join Date: Jun 2010
Posts: 12,688
|
|
Re: piaa lights wiring to inside of cab??
i ran my line for the hellas down along with the red brake light wires, drilled a hole in the bottom of the cab, and ran them up through there.
|
|
|