Ford Ranger Forum - Forums for Ford Ranger enthusiasts!

Go Back   Ford Ranger Forum - Forums for Ford Ranger enthusiasts! > > >
Forgot Password? Join Us!

Welcome to Ford Ranger Forum

Closed Thread
 
Thread Tools Search this Thread

  #1  
Old 02-05-2010, 07:16 PM
STL STL is offline
...............

 
Join Date: May 2009
Posts: 23,399
Default How To: 2007 foglight mod

Written by: The H.P Freak

Discussion Thread: How To: 2007 foglight mod


If you don't know what the "FOG LIGHT" mod is, well here ya go. On the RANGER, the lower fog lights will stay on when the normal head lights are on or the DRL (daytime running lights). As soon as you try to use your high beams the fog lights automatically shut off. This mod is to "OVERRIDE" this so you can run your fog lights and high beams at the same time.

- First the newer Rangers no longer have a GEM module. They use a SJB (smart junction box). It is located behind the P/S kick panel. Once you have the kick panel removed, locate the black connectors that you will need to tap into.





We will be working on the two top black connectors on the right hand side. We will call the very top one, "PLUG "A".
The 2ND black connector under that one will be called "PLUG "B".

You will need a RELAY and RELAY HARNESS. Remove the center wire from the RELAY HARNESS. It is not needed.

Here is the relay harness set-up I used :





Now you need to remove "PLUG "A" from the SJB. There is a small white lever in the middle of the plug. Simple pull the lever towards the rear of the truck. The plug will basically eject itself.

Now you need to only locate one wire in "PLUG "A". That would be the GREY/VIOLET (Grey wire with violet stripe). You need to TAP this wire, DO NOT CUT IT!!!!! If you cut this wire your in dash fog light warning light will no longer function.



I installed a tap connector onto the GREY/VIOLET wire.

Now you need to remove the 2ND black connector called "PLUG "B". Use the same procedure to remove this plug as you did to remove "PLUG "A".

There is only one wire you need to locate in "PLUG "B". That would be the small gauge, solid BROWN wire.You need to CUT this wire, making sure to leave enough wire on both ends in case you ever want to reverse this mod.



The BROWN wire going towards "PLUG"B" will be capped off. The BROWN wire going up, towards the dash will have to have a (MALE) connector installed on it. I used shrink tubing on this as well.

I used male/female electrical connectors so I could easily reverse this mod if needed to. Basically "PLUG & play".

Now I took the BLUE (#30) wire on my RELAY HARNESS and connected it to the small gauge SOLID BROWN wire.

Then I took the RED (#86) wire from my RELAY HARNESS and connected it to the GREY/PURPLE wire, via a TAP connector.

On my RELAY HARNESS, I took the ORANGE (#85) and YELLOW (#87)wires and tied them together with a ground connector. Both these wires will be used as GROUNDS. I used the small bolt at the bottom of the SJB as the grounding point.



Reinstall "PLUG "A/B" into the SJB and push the white lever towards the firewall to lock them back into place.

I ended up mounting my RELAY in the SJB. It fits nicely behind the P/S kick panel, out of site.

__________________
2005 Edge


Last edited by STL; 03-07-2010 at 03:03 PM.
Closed Thread

Thread Tools Search this Thread
Search this Thread:

Advanced Search


Similar Threads
Thread Thread Starter Forum Replies Last Post
Discuss How To: 2007 foglight mod THE H.P FREAK How-To Submissions 11 09-23-2016 10:22 AM
2007 ranger blinker mod... THE H.P FREAK Exterior Tech 1 05-08-2013 01:19 AM
My 2007 Ranger at the Dragstrip THE H.P FREAK Vehicle Videos 2 02-04-2010 12:16 PM
2007 4x4 trouble - Help Please!!! ian5001 Drivetrain Tech 4 01-11-2010 02:02 PM
2007 2wd lift kit Alfreado121 Lifted Suspension 1 10-17-2009 12:20 AM