|
|
|
|
08-20-2018, 12:21 PM
|
|
Demonic
|
|
Join Date: Mar 2017
Posts: 15
|
|
Clutch issue has me stumped
i have a 2000 ranger 3.0 with 5-speed transmission, had the clutch disc fail about a month ago due to leaking slave that i put off due to not wanting to drop the trans at the time. i have replaced my entire clutch system, disc, pressure plate combo from LUK (07-140), bought the entire hydraulic system (twice because i messed up the master the first time) and have bled the system 7 ways to sunday but cannot for the life of me figure out why the system wont even go into gear at this point. i know that the slave has plenty of travel and that the hydraulic system is bled properly, all the components are correctly installed ( have torn it apart and redone it 3 times to make sure everything was done correctly) if you can figure out what i am missing please speak up
have thrown a link to 4 videos i took yesterday to show my issue and the throw-out travel, 2 vids are engine off, 2 are truck running.
https://drive.google.com/file/d/1k9A...ew?usp=sharing
https://drive.google.com/file/d/1cGl...ew?usp=sharing
https://drive.google.com/file/d/19Fs...ew?usp=sharing
https://drive.google.com/file/d/14ox...ew?usp=sharing
__________________
- The Demon
2000 single cab 3.slow 5-speed 4x4 swapped trailhead edition sitting on 285/75/16s
northpeak4x4 front bumper, custom rear bumper with dual swingarms, 12°North LED pods, hi-lift and axe/shovel mounted in bed
Last edited by The Demon; 08-24-2018 at 03:30 PM.
|
|
|
|
Register and never see these ads again. |
|
08-20-2018, 12:53 PM
|
|
Ranger Driver
|
|
Join Date: Nov 2014
Posts: 376
|
|
Re: Clutch issue has me stumped
That seems more than enough travel on the clutch. I would take another look at the gear linkage...
|
08-20-2018, 01:35 PM
|
|
Ford Ranger Driver
|
|
Join Date: Jan 2009
Posts: 6,268
|
|
Re: Clutch issue has me stumped
Your levers inside the tranny are not lined up. Pull the shifter and then the stub and use a big screwdriver to line the 3 levers up inside the tranny, then reinstall the stub and the shifter. 10 minute fix.
Sent from my SM-J320V using Tapatalk
__________________
2004 Ext Cab, 4WD, 4.0, Auto, 154k. (4.0 engine is out of a 2009 Ranger w/96k) ( as of 7/1/2017)
2004 Ranger, Ext Cab, 2WD, 3.0, 5 speed , 4WABS, crank windows, no cruise, Edge 116k.(6/5,2014) (SOLD).
1999 Ford Ranger, Reg Cab, 2.5, 5 speed, 2WD, no AC, 150k (SOLD).
Last edited by modelageek; 08-20-2018 at 02:16 PM.
|
08-20-2018, 01:38 PM
|
Learning to use the forums
|
|
Join Date: Mar 2018
Posts: 8
|
|
Re: Clutch issue has me stumped
Did you get your flywheel resurfaced?
If so, you need to compensate for the different thickness with the appropriate shim to ensure proper clutch operation....just a thought.
Short of that, I would double check all of the part numbers of components used to make sure something wasn't substituted.
|
|
|
|
08-20-2018, 02:15 PM
|
|
Ford Ranger Driver
|
|
Join Date: Jan 2009
Posts: 6,268
|
|
Re: Clutch issue has me stumped
Quote:
Originally Posted by Vincenthdfan
Did you get your flywheel resurfaced?
If so, you need to compensate for the different thickness with the appropriate shim to ensure proper clutch operation....just a thought.
Short of that, I would double check all of the part numbers of components used to make sure something wasn't substituted.
|
I don't think that's it. Unless I misread his post. The OP is saying he can't move the shifter at all. My guess is he couldn't get the shifter detached from the stub(simple but weird bolt) in the tranny so he just removed the bolts holding in the stub and removed everything. The only issue is that the tranny needs to be in neutral when the stub is removed otherwise when you reinstall it it will be stuck in gear (hey ask me how I know this ) Again, if it's not in neutral and you reinstall the stub without lining up the shift levers then the shifter will not move at all. It will be stuck in gear even with the engine off.
Sent from my SM-J320V using Tapatalk
__________________
2004 Ext Cab, 4WD, 4.0, Auto, 154k. (4.0 engine is out of a 2009 Ranger w/96k) ( as of 7/1/2017)
2004 Ranger, Ext Cab, 2WD, 3.0, 5 speed , 4WABS, crank windows, no cruise, Edge 116k.(6/5,2014) (SOLD).
1999 Ford Ranger, Reg Cab, 2.5, 5 speed, 2WD, no AC, 150k (SOLD).
Last edited by modelageek; 08-21-2018 at 11:12 AM.
|
|
|
|
08-22-2018, 12:30 PM
|
|
Demonic
|
|
Join Date: Mar 2017
Posts: 15
|
|
Re: Clutch issue has me stumped
The shifter moves as can be seen in vids, but it doesnt seem to be going into any gear, with engine off it acts normal but when you start the engine it refuses to go into any gear
__________________
- The Demon
2000 single cab 3.slow 5-speed 4x4 swapped trailhead edition sitting on 285/75/16s
northpeak4x4 front bumper, custom rear bumper with dual swingarms, 12°North LED pods, hi-lift and axe/shovel mounted in bed
|
08-22-2018, 12:47 PM
|
|
Ford Ranger Driver
|
|
Join Date: Jan 2009
Posts: 6,268
|
|
Re: Clutch issue has me stumped
Did you at any time in the repair pull the shift stub out of the tranny?
I looked at 4 or 5 vids didn't see shifter in any. I'll go back and watch again
Sent from my SM-J320V using Tapatalk
----------
Quote:
Originally Posted by The Demon
The shifter moves as can be seen in vids, but it doesnt seem to be going into any gear, with engine off it acts normal but when you start the engine it refuses to go into any gear
|
I think I looked at all 16 vids. I didn't see a vid with the shifter in it. Only vids of pressure plate moving.
Sent from my SM-J320V using Tapatalk
__________________
2004 Ext Cab, 4WD, 4.0, Auto, 154k. (4.0 engine is out of a 2009 Ranger w/96k) ( as of 7/1/2017)
2004 Ranger, Ext Cab, 2WD, 3.0, 5 speed , 4WABS, crank windows, no cruise, Edge 116k.(6/5,2014) (SOLD).
1999 Ford Ranger, Reg Cab, 2.5, 5 speed, 2WD, no AC, 150k (SOLD).
|
|
|
|
08-22-2018, 01:10 PM
|
|
Ford Ranger Driver
|
|
Join Date: Jan 2009
Posts: 6,268
|
|
Re: Clutch issue has me stumped
Quote:
Originally Posted by The Demon
The shifter moves as can be seen in vids, but it doesnt seem to be going into any gear, with engine off it acts normal but when you start the engine it refuses to go into any gear
|
This is what the shift stub looks like. It's held in with bushings. When you remove it you can see inside the tranny like the 2nd pic shows. DID YOU AT ANY POINT REMOVE THE SHIFT STUB?
Sent from my SM-J320V using Tapatalk
----------
Quote:
Originally Posted by KenHigg
That seems more than enough travel on the clutch. I would take another look at the gear linkage...
|
I agree, does look like more then enough travel. These clutch master cylinders are suppose to be bleed outside of the truck.
Sent from my SM-J320V using Tapatalk
__________________
2004 Ext Cab, 4WD, 4.0, Auto, 154k. (4.0 engine is out of a 2009 Ranger w/96k) ( as of 7/1/2017)
2004 Ranger, Ext Cab, 2WD, 3.0, 5 speed , 4WABS, crank windows, no cruise, Edge 116k.(6/5,2014) (SOLD).
1999 Ford Ranger, Reg Cab, 2.5, 5 speed, 2WD, no AC, 150k (SOLD).
|
|
|
|
08-22-2018, 03:27 PM
|
Ford Ranger Driver
|
|
Join Date: Nov 2011
Posts: 1,965
|
|
Re: Clutch issue has me stumped
All I could see in 4 vids was of the slave working, if in fact the shifter is in, and will move through all 5 forward and rev when the engine is dead, its possible that the pilot bearing got damaged the first time the trans was installed, and is locking the input shaft to the crankshaft.
|
08-24-2018, 03:32 PM
|
|
Demonic
|
|
Join Date: Mar 2017
Posts: 15
|
|
Re: Clutch issue has me stumped
Shifter was pulled and a shifter rebuild kit went in while trans was out, just fixed the video links, hadnt noticed it was duplicated for just 1 of the 4 videos.
__________________
- The Demon
2000 single cab 3.slow 5-speed 4x4 swapped trailhead edition sitting on 285/75/16s
northpeak4x4 front bumper, custom rear bumper with dual swingarms, 12°North LED pods, hi-lift and axe/shovel mounted in bed
|
08-24-2018, 04:05 PM
|
|
Ford Ranger Driver
|
|
Join Date: Jan 2009
Posts: 6,268
|
|
Re: Clutch issue has me stumped
Quote:
Originally Posted by The Demon
Shifter was pulled and a shifter rebuild kit went in while trans was out, just fixed the video links, hadnt noticed it was duplicated for just 1 of the 4 videos.
|
Pull the stub and make sure the 3 levers are lined up in neutral then reinstall stub. I bet your issue has something to do with the stub/shifter being pulled.
Sent from my SM-J320V using Tapatalk
__________________
2004 Ext Cab, 4WD, 4.0, Auto, 154k. (4.0 engine is out of a 2009 Ranger w/96k) ( as of 7/1/2017)
2004 Ranger, Ext Cab, 2WD, 3.0, 5 speed , 4WABS, crank windows, no cruise, Edge 116k.(6/5,2014) (SOLD).
1999 Ford Ranger, Reg Cab, 2.5, 5 speed, 2WD, no AC, 150k (SOLD).
|
Thread Tools |
Search this Thread |
|
|
|
|