so idk whats up but the only thing that is workin with my system is my subs my door speakers stopped workin thier not blown helppppp

__________________
1996 Ranger XLT 2WD with a 97 4.0 engine

are your door speakes powered by an amp or Headunit

__________________

Truck: 2000 Ford Ranger XLT 4.0 4x4 ext cab
My Build Thread
Mod Ideas
Don't Forget to:
Create a Signature
Show your system

Mods: Brush guard|Front Hitch|Expo Roof Rack|Train Horn|Door/Dash/step/Hood Leds|2" lift|Rear Tow Points|On-Board Air System| 22" & 40" LED bar|and More!

Did all 2 or 4 stop at once? If so, it Could be a couple different things. Check for a grounded out speaker. If one speaker is grounded out it would shut all of them down.

__________________
'04 Sonic Blue Ranger, 2 tone Katzkin leather seats, Custom Ford script spray in liner, Spyder LED tails, 8000k Morimoto HID's, LED 3rd brake light + signal mirrors, 06 badges, grille, corners, K&N intake, Magnaflow exhaust, AR Shelby series 17x8 chrome wheels, Pioneer P4300DVD, Hybrid Audio Technologies Imagine 6.5 components up front and Pioneer TS-D681R's in rear, Alpine PDX-V9 5 channel Amp, Image Dynamics IDQ 12" sub. Optima Red Top, "Painted to match" interior pieces

they are not runnin off of my amp and all 4 stopped at one time

__________________
1996 Ranger XLT 2WD with a 97 4.0 engine

this or your HU is shot

Sent from my android phone using the FRF App

__________________

Truck: 2000 Ford Ranger XLT 4.0 4x4 ext cab
My Build Thread
Mod Ideas
Don't Forget to:
Create a Signature
Show your system

Mods: Brush guard|Front Hitch|Expo Roof Rack|Train Horn|Door/Dash/step/Hood Leds|2" lift|Rear Tow Points|On-Board Air System| 22" & 40" LED bar|and More!

a 96 ford ranger( If it had a factory cassette and had an auto set button on the radio) has a factory amplifier. On your wire harness adaptor you need to make sure any blue/ blue/white wires are hooked up.. they may have come loose. If everything looks good as far as wiring your amplifier may have went bad. If thats the case you can go to the amplifier location and splice the inputs to the outputs and run the speakers directly from your head unit. Below is the wiring info for your truck


1996-97 Ford Ranger
Premium Sound System

FUNCTION PIN WIRE COLOR
Accessory 12 Volt 6 YW/BK
Constant 12 Volt 8 L.GN/VT
Chassis Ground 7
3 BK
BK/L.GN
Power Antenna
Remote 1 D.BU
Illumination
Dimmer 5 L.BU/RD
FUSE VALUE FUSE LABEL FUSEBOX LOCATION
7.5 AMP #20 DRIVER'S SIDE DASH ENDCAP
10 AMP #29 DRIVER'S SIDE DASH ENDCAP

Amplifier Note:
The amplifier in this vehicle has been found in three locations
1. Passenger's side kickpanel
2. Below the R/R speaker (SuperCab models)
3. On the floor behind the R/R seat (Standard Cab models)
Left Front + To Amp 20 L.GN
Left Front - To Amp 21 WT/OG
Right Front + To Amp 12 WT/RD
Right Front - To Amp 13 BN
Left Rear + To Amp 22 L.BU/BK
Left Rear - To Amp 23 YW
Right Rear + To Amp 14 VT/WT
Right Rear - To Amp 15 L.BU


Back to top


--------------------------------------------------------------------------------
Premium Sound Amplifier Wiring
FUNCTION PIN WIRE COLOR
Constant 12 Volt 1 L.GN/VT
Chassis Ground 2 BK/L.GN
Amp Remote 3 D.BU
Left Front Spkr + 7 OG/L.GN
Left Front Spkr - 8 L.BU/WT
Left Rear Spkr + 9 GY/L.BU
Left Rear Spkr - 10 TN/YW
Right Front Spkr + 11 WT/L.GN
Right Front Spkr - 12 D.GN/OG
Right Rear Spkr + 13 OG/RD
Right Rear Spkr - 14 BN/PK
FUNCTION PIN WIRE COLOR
Right Rear - Input 15 L.BU
Right Front - Input 16 BN
Left Rear - Input 17 YW
Left Front - Input 18 WT/OG
Right Rear + Input 19 VT/WT
Right Front + Input 20 WT/RD
Left Rear + Input 21 L.BU/BK
Left Front + Input 22 L.GN


Back to top


--------------------------------------------------------------------------------
Video and Navigation Wires FUNCTION LOCATION COLOR
Vehicle Speed Sensor Pin #20 of 40-pin plug*, L/R corner under hood by brake reservoir GY/BK
Reverse Light ( + ) Pin #8 of 40-pin plug*, L/R corner under hood by brake reservoir BK/PK
Parking Brake ( - ) At parking brake switch L.GN/RD
Brake Light ( + ) At brake pedal switch L.GN
*These are actually two different 40-pin plugs located in a group of three similar plugs.


Back to top

If you were using your stock speaker wiring to high level input on the sub amp, that is your problem, because those wires are coming off the stock amp. Bad mojo.

thanks for the help i aint been on in a while but the problem was one of my speakers were grounded

__________________
1996 Ranger XLT 2WD with a 97 4.0 engine

You're welcome man, that's what I figured it was. Glad you got it fixed man

__________________
'04 Sonic Blue Ranger, 2 tone Katzkin leather seats, Custom Ford script spray in liner, Spyder LED tails, 8000k Morimoto HID's, LED 3rd brake light + signal mirrors, 06 badges, grille, corners, K&N intake, Magnaflow exhaust, AR Shelby series 17x8 chrome wheels, Pioneer P4300DVD, Hybrid Audio Technologies Imagine 6.5 components up front and Pioneer TS-D681R's in rear, Alpine PDX-V9 5 channel Amp, Image Dynamics IDQ 12" sub. Optima Red Top, "Painted to match" interior pieces