Anyone that has done a V8 ranger, dreamed of doing or is in the process has read the TRS article "Swapping An Explorer 5.0L In To A 1998-Up Ranger"

I have some additions, things they left out that might be helpful.

They: "Using the Explorer 5.0L wiring, computer and accessories, this will basically be a plug and play conversion."

Add this: "after you have done it 3 or 4 times"


They: "The two biggest problems you could run in to doing this swap would be the PATS and VSS."

Add this: "There will be tens of dozens of little problems you will face also"

They: "The easiest V8 donor for a 1998-2007 Ranger 4x4 swap would be the 1996-2001 Explorer/Mountaineer 5.0 AWD."

Some big additions:

"Remember if your donor vehicle has power windows and power seats to move the seat all the way back to be able to easily access under the dash, also roll the windows up before removing the battery and wiring harness. Failure to do so will result in animals making homes inside, mammals as well as stinging insects especially if you leave it sitting for most of a year in an open field."

"If you leave the transmission in the donor and pull the motor only, do not remove the transmission dip stick tube until you have everything you want to remove by crawling under the vehicle first. Having 10 gallons of floor dry or kitty litter works also but not as easy."

"The temperature sensor for the overhead console is not necessarily in the spot that every article on the internet says it is. It might just be on the driver side."

"The most likely place for a huge mud based wasp nest it behind the dash to the right of the instrument cluster. Being able to run quickly will minimize bodily damage. There might also be additional hornet nests in the door panels if you leave them open."

Now on the vehicle the motor is being installed in.

"Make sure you are not following the 4 wheel drive V6 tutorial if doing a coil spring 2WD ranger born with a 4 cyl, you will waste a lot of money on wrong mounts, wrong plates and general headaches on every detail. Good luck finding 100% reliable info on the coil spring swaps even from people who design the mounting plates. Plan on spending 3 or 4 times the money you budgeted, plan on it taking at least 10 times longer than the articles you will read."


Maybe eventually I will finish it. I hope.

__________________
00 XLT 4WD XCSB 4.0 my new baby
00 XLT 2WD RCSB 5.0 swap in progress.
98 XLT 4WD XCSB 4.0 dead
99 EXPO donor motor for dead one and parts for the others.
Newest Ranger Forum

For me, the $550.00 custom 2 piece driveshaft was the big surprise.

I'd waded through wiring diagrams till my eyes bled. Read and researched as much as I could. Savaged a couple wrecks in a breakers yard for the wiring plugs so I could make wiring adapters to make the conversion as plug and play as possible.

The entire swap went really well, but it took as long to get the driveshaft made as it did for the rest of the swap and the cost of the shaft was shocking.

Guess I should have said I was swapping in an old Pinto 2.0 and only needed a driveshaft for an 80 hp drivetrain.

This is refreshing for me. I've been on TRS and not a lot of 2wd v8 info over there.

__________________
I ask the dumb questions so you don't have to.
2001 2wd swb Ranger EDGE. 3.n0 with 5 spd. Bare bones.Very simple but tough truck.
MODS: '93 Lincoln Town car wheels: Explorer seats and center console. More to come...
Build thread comiming soon .... when I get a donor

subb'd!

__________________
1999 xlt 2.5l 5-speed Supercab 159k
83 diesel 2.2l na
06 F250 6.0l psd
{click for lol}

I'm stunned your driveshaft cost was that high. I took two used shafts for the front and rear that had the ends I needed into a local shop. They cut and balanced and installed new Spicer joints in both for $225 total.

__________________
1999 5.0/4R70W/4406 Ext. Cab

Do I know y'all?

__________________
00 XLT 4WD XCSB 4.0 my new baby
00 XLT 2WD RCSB 5.0 swap in progress.
98 XLT 4WD XCSB 4.0 dead
99 EXPO donor motor for dead one and parts for the others.
Newest Ranger Forum

Did you finish the swap?

__________________
1999 5.0/4R70W/4406 Ext. Cab

Subed…..lol

__________________
2000 Ford Ranger XLT 2WD ~ Work-In-Progress: 5.0 V8, M5R2 5 Speed, 4" Suspension Lift, 3" Body Lift, 33" BFG's, Bilstein 5100's, Comp Cams XE258HR-12, 24# Injectors, Torque Monster Headers, Flowmaster 70 Series,
1987 Ford F-150 Lariat 302 ~ Decommissioned
2006 Honda Civic LX 1.6 ~ Totaled
2011 Acura TSX K24 Base ~ Daily Driver, Supercharged 10PSI, 310whp 241lb/ft

Another subscriber here :-)
Can't wait to hear more about this swap.

Thanks guys, I moved to another forum and have purchased my dream ranger... about the same thing as the 2WD just a 4WD. Single cab, short bed, same color, same year.

The 5.0 is in the 2wd now, transmission is in, but I am considering using it as a parts vehicle and putting everything I have done in to the 4WD..

This is the original build thread on this forum: Thee Gherkin build, 5.0

Have hooked up with a serious group of modders and swappers over at the forum in my sig.

__________________
00 XLT 4WD XCSB 4.0 my new baby
00 XLT 2WD RCSB 5.0 swap in progress.
98 XLT 4WD XCSB 4.0 dead
99 EXPO donor motor for dead one and parts for the others.
Newest Ranger Forum