Ford Ranger Forum - Forums for Ford Ranger enthusiasts!

Go Back   Ford Ranger Forum - Forums for Ford Ranger enthusiasts! > > >
Forgot Password? Join Us!

Welcome to Ford Ranger Forum

Reply
 
Thread Tools Search this Thread

  #1  
Old 04-18-2010, 03:13 PM
scorb scorb is offline
Learning to use the forums
 
Join Date: Jan 2010
Posts: 5
Default replaced crankshaft position sensor now the truck wont start

my truck is a 99 4x4 with a 3.0. yesterday my cel came on so i took it to autozone and they told me it was the crankshaft position sensor. i replaced it today and now the truck will crank but not start.
__________________
99 Ford Ranger 4x4 stepside 3.0
Reply With Quote
  #2  
Old 12-06-2011, 08:36 PM
zippo zippo is offline
Learning to use the forums
 
Join Date: Dec 2011
Posts: 1
Default Re: replaced crankshaft position sensor now the truck wont start

hey dude i have the same truck but mine is a two wheel drive 3.0 and i did the same thing and now my truck wont start. found the problem replacment part duralast su4101 crank sensor is a bad replacement part. the plug is not made the same as the factory part THANKS ALOT AUTO ZONE!

Last edited by zippo; 12-07-2011 at 12:25 AM. Reason: SOLDED BAD PART BY AUTO ZONE
Reply With Quote
  #3  
Old 12-06-2011, 09:09 PM
02RangerFX4 02RangerFX4 is offline
Lil' Red
 
Join Date: Jan 2011
Posts: 6,369
Default Re: replaced crankshaft position sensor now the truck wont start

Make sure you put it on right. Its sensing when the crankshaft is in the correct position, if its not on right, it wont start.
__________________
2002 ford ranger FX4 Off Road | 4.0l v6 | Flowmaster 40 S/I D/O | JBA Headers | Rebello Racing cams | port and polished heads | K&n Drop-in filter | TwinStick | 31 Spline 4.10 Torsen rear diff | Alcoa rims | Sitting on 31's|
Reply With Quote
  #4  
Old 04-07-2012, 02:24 PM
Huck Huck is offline
13mm Guru
 
Join Date: Apr 2011
Posts: 115
Send a message via Skype™ to Huck
Default Re: replaced crankshaft position sensor now the truck wont start

I have narrowed my problem down to the same thing. I found out that it takes a special tool to dial it in properly.
__________________
1992 XLT.
2.3 Eight plug w/5 speed
High flow filter with functional scoop.
http://www.fuelly.com/smallsig-us/70702.png
Reply With Quote
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search


Similar Threads
Thread Thread Starter Forum Replies Last Post
my truck is a ford 2000 ranger and it will start but wont move? jayborja02 Drivetrain Tech 4 08-13-2012 08:35 AM
1996 Ranger crankshaft position sensor vang0017 4.0 SOHC / 4.0 OHV Tech 5 06-07-2011 06:59 PM
Truck still wont start all new ignition parts rumpranger 4-Cylinder Tech 0 01-04-2010 04:24 PM
Truck wont start tj88 Drivetrain Tech 1 08-01-2009 02:31 PM
Cam Position Sensor/CEL Nightmare beat_1998_2.5l 4-Cylinder Tech 0 07-28-2009 07:54 AM